background image

 

 

 

DINUY S.A.

   c/Auzolan 2, 20303 Irun (SPAIN

                         Tel.: +34 943627988 – E-mail: 

 

o

 

Cyclic OFF Telegram: OFF
transmission’ x ‘Time Factor for cyclic transmission’

o

 

No telegram: nothing is sent

 

Value (EIS6): It sends a value between 0 and 255. Can be selected if in case of detection ('Sending at the begin
detection') or at the end ('Sending at the end of detection') is sent 
not sending any telegram. 

Sensibility (threshold) 

Allows making more or less sensitive to movements the detector

movement, while a low sensitivity (255) prevents unwanted false detections

5 – Twilight Sensor 

5.1 – Parameters 

Activate object Twilight sensor 

Enable or disable this feature using an external device.
Possible to select the trigger telegram (‘Enabling Twilight sensor with’):

 

ON Telegram 

 

OFF Telegram 

 Enabled Object:  

Behavior on bus voltage recovery – comm. object 
Sets the 'Twilight sensor enable' object behavior after a power failure of the Bus

After recovering the Bus can be enabled or not to consult the state of this object

Type of Twilight object 

Defines the type of object 'Twilight Telegram sensor', which will be sent reach

level: 

 

Switching (EIS1): sends an object of one bit (0, 1). Can be selected if in case of reaching the minimum threshold 
('Sending at low Threshold') or the maximum threshold of lux ('Sending at high Threshold') is sent

o

 

ON Telegram 

o

 

OFF Telegram 

o

 

Cyclic ON Telegram: ON is sent perio
transmission’ x ‘Time Factor for cyclic transmission’

 

 

SPAIN) 

mail: 

[email protected]

 – Web: 

www.dinuy.com

  

 is sent periodically. The time between two sending: ‘Time Base for cyclic 

’ x ‘Time Factor for cyclic transmission’. 

nothing is sent. 

It sends a value between 0 and 255. Can be selected if in case of detection ('Sending at the begin

('Sending at the end of detection') is sent a value between 0% and 100%, in steps of 10%, or 

Allows making more or less sensitive to movements the detector. A high sensitivity (1) makes detecting the sligh

movement, while a low sensitivity (255) prevents unwanted false detections. 

Enable or disable this feature using an external device. 

(‘Enabling Twilight sensor with’): 

comm. object Twilight sensor enable 

object behavior after a power failure of the Bus. 

Bus can be enabled or not to consult the state of this object. 

Defines the type of object 'Twilight Telegram sensor', which will be sent reaching the maximum

ends an object of one bit (0, 1). Can be selected if in case of reaching the minimum threshold 

('Sending at low Threshold') or the maximum threshold of lux ('Sending at high Threshold') is sent

Cyclic ON Telegram: ON is sent periodically. The time between two sending: ‘Time Base for cyclic 
transmission’ x ‘Time Factor for cyclic transmission’. 

 

 

is sent periodically. The time between two sending: ‘Time Base for cyclic 

It sends a value between 0 and 255. Can be selected if in case of detection ('Sending at the beginning of 

between 0% and 100%, in steps of 10%, or 

A high sensitivity (1) makes detecting the slightest 

 

the maximum and minimum threshold light 

ends an object of one bit (0, 1). Can be selected if in case of reaching the minimum threshold 

('Sending at low Threshold') or the maximum threshold of lux ('Sending at high Threshold') is sent: 

dically. The time between two sending: ‘Time Base for cyclic 

Содержание DM KNT 002











Отзывы: