KNOVA KN CS-3555R, Руководство пользователя

Страница: 2 / 36

Product specifications ......................................................... 1
Warnings .............................................................................. 1
Symbols .............................................................................. 1
Power tool safety ................................................................ 2
Chop Saw Safety ................................................................ 3
Electrical requirements and safety ...................................... 5
Tools Needed For Assembly ............................................... 6
Carton contents .................................................................. 6
Know your Chop Saw .......................................................... 7 Assembly ........................................................................... 8
Adjustments ..................................................................... 9
Operation ........................................................................... 10
Maintenance ...................................................................... 11
Troubleshooting guide ........................................................ 12
Parts list and schematic (motor)......................................... 13
Parts list ............................................................................. 14
Schematic ........................................................................... 15
PRODUCT SPECIFICATIONS
MOTOR
Type: Universal
Amps:
15
Maximum hp: 3.5
Voltage: 120
Hz: 60
RPM (No load)
3600
TABLE OF CONTENTS
1
WARNINGS
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals
known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemical:
work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to
fiter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective
clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING
SYMBOLS
WARNING ICONS
Your power tool and its Instruction Manual may contain “WARNING ICONS” (a picture symbol intended to alert you to, and/or
instruct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate
your tool better a. safer. Shown below are some of the symbols you may see.
SAFETY ALERT: Precautions that involve your safety.
PROHIBITION
WEAR EYE PROTECTION: Always wear safety
goggles or safety glasses with side shields.
READ AND UNDERTAND INSTRUCTION MANUAL:
To reduce the risk of injury, user and all bystanders
must read understand instruction manual before using
this product.
KEEP HANDS AWAY FROM BLADE: Failure to
keep your hands away from the blade will result
in serious personal injury.
SUPPORT AND CLAMP WORK
CUTTING WHEEL
Diameter:
14 in.
Arbor: 1 in.
WARNING
To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection. This tool is wired at
the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker.
To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.
Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in
serious injury to you or damage to the tool.
CUTTING CAPACITY
Cross Cut 0°:
Round: 5 in.
Square: 4-3/4 in. × 4-3/4 in.
3 in. × 8-1/4 in.
Rectangular: 4-1/4 in. × 6-1/8 in.
4-1/2 in. × 5-1/8 in.
CUTTING CAPACITY
Miter Cut 45°:
Round: 4 in.
Square: 4 in. × 4 in.
Rectangular: 3-1/3 in. × 5 in.
Vise clamp angle:
0° ~ 45°
WEAR RESPIRATORY AND HEARING
PROTECTION: Always wear respiratory
and hearing protection.
DANGER
DANGER: Indicates an inminently
hazardous situation which, if not avoided, will result
in death or serious injury.