Fig 2
•
Remove the terminal access cover with the aid of a slotted screwdriver (see Fig 3)
Fig 3
•
Connect the Live (brown), Neutral (blue) and Earth (green and yellow) to the push-fit terminal block ensuring the
correct polarity is observed (see Fig 4)
•
Ensure the strain relief is used to secure the mains input cable
Fig 4
•
Loop in / loop out wiring can be achieved with the push-fit terminal block
•
Push up both of the spring clips either side of the fitting and position into the ceiling (see Fig 5)
•
Ensure glass/mineral wool insulation is not packed tightly around the fitting, but that it is loosely placed
unbroken over the top of the luminaire. This is to allow heat dissipation from the light source
Pull up the
terminal block
cover
Neutral (blue)
Earth (green/yellow)
Live (brown)
Cable clamp
Fig 2
•
Remove the terminal access cover with the aid of a slotted screwdriver (see Fig 3)
Fig 3
•
Connect the Live (brown), Neutral (blue) and Earth (green and yellow) to the push-fit terminal block ensuring the
correct polarity is observed (see Fig 4)
•
Ensure the strain relief is used to secure the mains input cable
Fig 4
•
Loop in / loop out wiring can be achieved with the push-fit terminal block
•
Push up both of the spring clips either side of the fitting and position into the ceiling (see Fig 5)
•
Ensure glass/mineral wool insulation is not packed tightly around the fitting, but that it is loosely placed
unbroken over the top of the luminaire. This is to allow heat dissipation from the light source
Pull up the
terminal block
cover
Neutral (blue)
Earth (green/yellow)
Live (brown)
Cable clamp
Fig 2
•
Remove the terminal access cover with the aid of a slotted screwdriver (see Fig 3)
Fig 3
•
Connect the Live (brown), Neutral (blue) and Earth (green and yellow) to the push-fit terminal block ensuring the
correct polarity is observed (see Fig 4)
•
Ensure the strain relief is used to secure the mains input cable
Fig 4
•
Loop in / loop out wiring can be achieved with the push-fit terminal block
•
Push up both of the spring clips either side of the fitting and position into the ceiling (see Fig 5)
•
Ensure glass/mineral wool insulation is not packed tightly around the fitting, but that it is loosely placed
unbroken over the top of the luminaire. This is to allow heat dissipation from the light source
Pull up the
terminal block
cover
Neutral (blue)
Earth (green/yellow)
Live (brown)
Cable clamp
Fig 5
VFRDGICxx and VFRSGICxx
•
Remove the lock-ring of the bezel by turning anti-clockwise 45˚
•
Insert a GU10 lamp into the lock-ring lamp clip and connect a lamp to the lamp holder
•
Push the lamp and lock-ring up into position in the downlight body and secure the lock-ring by turning clockwise
45˚ (see Fig 6)
Fig 6
VFRSHGICxx
•
When using an IP65 bezel, please ensure both gaskets are in place. One gasket is pre-installed with the bezel and
the second gasket should be installed around the base of the fitting (see Fig 7)
• Remove the terminal access
cover with the aid of a slotted
screwdriver (see Fig 3)
• Connect the Live (brown), Neutral
(blue) and Earth (green and yellow)
to the push-fit terminal block
ensuring the correct polarity is
observed (see Fig 4)
• Ensure the strain relief is used to
secure the mains input cable
• Loop in / loop out wiring can be achieved
with the push-fit terminal block
• Push up both of the spring clips either
side of the fitting and position into the
ceiling (see Fig 5)
• Ensure glass/mineral wool insulation is
not packed tightly around the fitting, but
that it is loosely placed unbroken over the
top of the luminaire. This is to allow heat
dissipation from the light source
3
Fig 3
Fig 4
Fig 5
(VFRDGICxx and VFRSGICxx)
• Remove the lock-ring of the bezel by
turning anti-clockwise 45˚
• Insert a GU10 lamp into the lock-ring
lamp clip and connect a lamp to the lamp
holder
• Push the lamp and lock-ring up into
position in the downlight body and secure
the lock-ring by turning clockwise 45˚
(see Fig 6)
Fig 5
VFRDGICxx and VFRSGICxx
•
Remove the lock-ring of the bezel by turning anti-clockwise 45˚
•
Insert a GU10 lamp into the lock-ring lamp clip and connect a lamp to the lamp holder
•
Push the lamp and lock-ring up into position in the downlight body and secure the lock-ring by turning clockwise
45˚ (see Fig 6)
Fig 6
VFRSHGICxx
•
When using an IP65 bezel, please ensure both gaskets are in place. One gasket is pre-installed with the bezel and
the second gasket should be installed around the base of the fitting (see Fig 7)
Fig 6
(VFRSHGICxx)
