background image

 

 

Fig 2 

 

 

Remove the terminal access cover with the aid of a slotted screwdriver (see Fig 3) 

 

 

Fig 3  

 

Connect the Live (brown), Neutral (blue) and Earth (green and yellow) to the push-fit terminal block ensuring the 

correct polarity is observed (see Fig 4) 

 

Ensure the strain relief is used to secure the mains input cable 

 

 

Fig 4 

 

Loop in / loop out wiring can be achieved with the push-fit terminal block 

 

Push up both of the spring clips either side of the fitting and position into the ceiling (see Fig 5) 

 

Ensure glass/mineral wool insulation is not packed tightly around the fitting, but that it is loosely placed 

unbroken over the top of the luminaire. This is to allow heat dissipation from the light source 

Pull up the 

terminal block 

cover 

Neutral (blue) 

Earth (green/yellow) 

Live (brown) 

Cable clamp 

2

These instructions should be read carefully and retained after installation by the end user for 
future reference and maintenance.
These instructions should be used to aid installation of the following products:
VFRDGICxx / VFRSGICxx / VFRSHGICxx

GENERAL INSTRUCTIONS

SAFETY

INSTALLATION

•  Installation of this luminaire should only be carried out by a qualified electrician or competent 

person to the current Building and IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance
•  Check the total load on the circuit (including when this luminaire is fitted) does not exceed the 

rating of the circuit cable, fuse or circuit breaker

•  Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for 

installation - VFRDGICxx and VFRSGICxx are IP20 rated and VFRSHGICxx is IP65 rated

• These products are Class I and must be earthed
• These products are dimmable dependant on lamp type (lamp not included)
•  These products are IC rated and are suitable for use with glass/mineral wool insulation  

See the 

Warning section for further information

• Provide power to the point of installation
•  Cut a suitable hole in the ceiling as per the cut-out details in Fig 1 ensuring it does not 

infringe with electrical cables, water/gas pipes or ceiling joists

•  Fold out the terminal bracket until it 

locks into position (see Fig 2)

VFRxxxx Series 

These instructions should be read carefully and retained after installation by the end user for future reference and 

maintenance. 

These instructions should be used to aid installation of the following products: 

VFRDGICxx / VFRSGICxx / VFRSHGICxx 

SAFETY 

 

Installation of this luminaire should only be carried out by a qualified electrician or competent person to the 

current Building and IEE Wiring Regulations (BS7671) 

 

Please isolate mains prior to installation/maintenance 

 

Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the 

circuit cable, fuse or circuit breaker 

 

Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation 

VFRDGICxx and VFRSGICxx are IP20 rated and VFRSHGICxx is IP65 rated 

 

These products are Class I and must be earthed 

 

These product are dimmable dependant on lamp type (lamp not included) 

 

These products are IC rated and are suitable for use with glass/mineral wool insulation. See the warning 

section for further information 

 

INSTALLATION 

 

Provide power to the point of installation 

 

Cut a suitable hole in the ceiling as per the cut-out details in Fig 1 ensuring it does not infringe with electrical 

cables, water/gas pipes or ceiling joists 

 

 

Part code 

Cut-out (mm) 

VFRDGICxx 

72 

VFRSGICxx 

84 

VFRSHGICxx 

72 

 

        

 

Fig 1 

 

 

Fold out the terminal bracket until it locks into position (see Fig 2) 

See table for cut-out (mm) 

Fig 1

Part code

Cut-out

VFRDGICxx

72mm

VFRSGICxx

84mm

VFRSHGICxx

72mm

Fig 2

Отзывы: