B
C
D
A
Operating Instructions:
Portable Patio Mini Post and Convenience Outlet are for
temporary use and not for permanent installation.
e Convenience outlet on this portable post has a GFCI
(Ground Fault Circuit Interrupter) safety outlet feature. In the
event of a ground fault, the GFCI will trip and stop the fl ow
of electricity to prevent serious injury.
To use outlet, lift outlet cover to plug in other working,
outdoorrated devices, such as additional Portable Patio Mini
Post lights or temporary devices such as portable radios. Allow
the outlet cover to partially close over the plug, as shown in
Diagram (A), to protect the outlet from the elements. Keep
cover of Convenience outlet closed when not in use.
Portable mini post must be plugged in to an active outlet
in order for the convenience outlet to operate.
If Mini Post light or appliances plugged into Convenience
Outlet do not operate, see procedure for resetting and testing
GFCI outlet.
DIAGRAM (A) GRAPHIC:
Shows base of unit
with plug in use and cover partially closed.
Resetting and Testing Procedure:
(1) Make sure the Portable Patio Mini Post is plugged
into an active electrical outlet.
(2) Plug a radio, another light or other working outdoor rated
device into the (GFCI) Convenience Outlet.
(3) Press the RESET button fully. Turn power on for the
device that is plugged into convenience outlet to verify
that power is on.
(4) Press the TEST button in order to trip the safety device.
is should stop the fl ow of electricity causing the
additional device to turn off . Note that the RESET
button will pop out.
(5) To restore power, Press the RESET button.
(6) Test the outlet monthly to assure proper and safe operation
by following steps 4 and 5.
DIAGRAM (B) GRAPHIC:
Close-up of outlet clearly
shows the TEST & RESET Buttons.
Proper Care/Cleaning:
In order to maximize the appearance of a Prime Outdoor
Fixture, it is important that dust and debris is removed from
the surface of the lantern periodically. It is recommended that
the lantern be wiped down weekly using a soft, dry or damp
cloth. DO NOT use any abrasives such as glass cleaners or
chemicals, as this will scratch, remove, or damage the protec-
tive coating, allowing moisture and pollutants to come in
contact with the metal.
SAVE THESE INSTRUCTIONS!!
Assembly Screw
Rubber
Washer
100 Watt Medium
100 Watt Medium
Base Bulb
Base Bulb
DO NOT PLACE NEAR
SPRINKLER OR
IRRIGATION SYSTEMS.
DO NOT PLACE NEAR
STANDING WATER OR
WITHIN 16 FEET OF
POOL OR SPA.
E1
Printed in China • March 2005
©2005 Craftmade • 650 S Royal Lane
Coppell, TX USA 75019
Z9240 Outdoor Portable Post Assembly Instructions
Read All Instructions
Estimated assembly time is 35 minutes.
Caution:
is lamp is partially assembled in the factory by qualifi ed craftsman. Some assembly is required before use. Please
follow the assembly instructions carefully.
WARNING!!
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY:
When using outdoor use portable lamps, basic safety precautions should always be followed to reduce the risk of
fi re, electric shock, and personal injury, including the following.
• Use only three-wire outdoor extension cords that have three prong grounding plugs and grounding receptacles
that accept the appliance’s plug.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used
for the wet location portable lamp. Receptacles are available having built-in GFCI protection and are able to be
used for this measure of safety.
• Use only with an extension cord for outdoor use, such as an extension cord of cord type SW, SW-A, SOW,
SOW-A, STW, STWA, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTWA, or SJTOW, SJTOW-
A.
• Turn off /unplug lamp and allow to cool before replacing bulb.
• Do not touch bulb when fi xture is turned on.
• Do not look directly at lighted bulb.
PORTABLE LANTERN SUITABLE FOR WET LOCATION USE.
CAUTION: RISK OF ELECTRIC SHOCK,
Do not use with extension cord near water or where water may
accumulate. Keep lamp at least 16 feet from pools and spas. Keep plugs and receptacles dry.
FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
Assembly: (refer to Fig 1)
1.) Attach tube (C) to base (D)
2.) Attach tube (B) to tube (C)
3.) Attach fi xture head (A) to tube (B)
4.) Pull excess cord through bottom of base until tight.
Bulb Installation: (refer to Fig 2)
1.) Remove assembly screws on fi xture roof
and insert bulb. Reattach roof.
Use one 100 Watt Max Medium
Base Bulb. (Not Included.)
--CAUTION--
Be careful to align threads properly while
assembling. DO NOT CROSS-THREAD
Stop and unscrew if alignment begins to
appear “off “. Then begin assembly again.
DIAGRAM (A)
�
�
�
�
�
�
�
�
�
�
�
�
�
�� ����
�
�
�
�
�� ��������
�
�
�
�
�
�
�
�
�
�
�
�
�
�
���
���
�
�
�
�
�
Fo
llo
w
D
ir
ec
tio
ns
S
ui
ve
z
In
st
ru
ct
io
ns
Te
st
M
on
th
ly
Te
st
M
en
su
el
Reset Re
set
Test Tes
t
Fo
llo
w
D
ir
ec
tio
ns
S
ui
ve
z
In
st
ru
ct
io
ns
Te
st
M
on
th
ly
Te
st
M
en
su
el
Reset Re
set
Test Tes
t
DIAGRAM (B)
E2
If fi xture does not work:
1. Turn off electrical power and check all wire connections.
2. Check fuse or circuit breaker and replace if necessary.
3. Check to make sure light bulb is in working order.
4. Ensure that dimmer switch is in the “on” position.
TROUBLESHOOTING
