22
7.1.1
Switch on the device
Once connected to the correct supply voltage, the device starts and is operational. The LED
display indicates the status.
To operate via the app , the Bluetooth® LE signal on the smartphone or tablet must be
switched on.
1. Download and install App.
2. Start App.
3. Select the device from the displayed livelist. All available devices are displayed.
4. Enter username -> admin
5. Enter initial password -> instrument serial number
6. After the first login it is recommended to change your username and password.
7.1.2
LED display
LED messages signal the status of the device and sensor.
LED behavior
Status
Green
Flashes quickly
Everything OK
Device starting up
Green
Flashes twice
Everything OK
Read out Memosens sensor information from sensor to transmitter (sensor type,
calibration data, etc.)
Green
Flashes slowly
Everything OK
Sensor and device OK and functioning correctly.
Green
Flashes quickly three times
Everything OK
Measured value at PLC in automatic HOLD.
If the "Sensor replacement alarm delay" is exceeded, the device transmits a signal on
alarm.
The automatic hold is set to 30 seconds but can be configured to suit the customer's
needs.
Red
Flashes quickly
Failure of device or sensor Fault
state as per NAMUR NE107
Red, green
Three red flashes alternating
with three green flashes
Squawk
Squawk is signaled briefly while the connection is established. Squawk can also be
activated via the app. This makes it possible to locate the device more quickly, e.
g. when
several devices are installed, you can see which one the connection is established with.
23
Sommaire
1
Informations relatives au document ............................................................ 24
1.1
Mises en garde..................................................................................................................................... 24
1.2
Symboles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................................................... . . . . . 24
1.3
Symboles sur l'appareil ....................................................................................................................... 24
2
Consignes de sécurité fondamentales .......................................................... 25
2.1
Exigences imposées au personnel ....................................................................................................... 25
2.2
Utilisation conforme ............................................................................................................................ 25
2.3
Sécurité du travail ................................................................................................................................ 25
2.4
Sécurité de fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................................... . 25
2.5
Sécurité du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................................................ . . 26
3
Description du produit ....... ....... ...................................................................... 27
3.1
Construction de l'appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....................................................... . . . . . 27
4
Réception des marchandises et identification des produits ....................... 27
4.1
Réception des marchandises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................................................... . . 27
4.2
Identification du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................................................ 28
5
Raccordement électrique ..... ..... ..................................................................... 28
5.1
Environnement ................................................................................................................................... 29
6
Intégration système ....................................................................................... 29
6.1
Intégration de l'appareil dans le système ............................................................................................ 29
7
Mise en service ................................................................................................ 31
7.1
Contrôle du fonctionnement ............................................................................................................... 31
22
7.1.1
Switch on the device
Once connected to the correct supply voltage, the device starts and is operational. The LED
display indicates the status.
To operate via the app , the Bluetooth® LE signal on the smartphone or tablet must be
switched on.
1. Download and install App.
2. Start App.
3. Select the device from the displayed livelist. All available devices are displayed.
4. Enter username -> admin
5. Enter initial password -> instrument serial number
6. After the first login it is recommended to change your username and password.
7.1.2
LED display
LED messages signal the status of the device and sensor.
LED behavior
Status
Green
Flashes quickly
Everything OK
Device starting up
Green
Flashes twice
Everything OK
Read out Memosens sensor information from sensor to transmitter (sensor type,
calibration data, etc.)
Green
Flashes slowly
Everything OK
Sensor and device OK and functioning correctly.
Green
Flashes quickly three times
Everything OK
Measured value at PLC in automatic HOLD.
If the "Sensor replacement alarm delay" is exceeded, the device transmits a signal on
alarm.
The automatic hold is set to 30 seconds but can be configured to suit the customer's
needs.
Red
Flashes quickly
Failure of device or sensor Fault
state as per NAMUR NE107
Red, green
Three red flashes alternating
with three green flashes
Squawk
Squawk is signaled briefly while the connection is established. Squawk can also be
activated via the app. This makes it possible to locate the device more quickly, e. g. when
several devices are installed, you can see which one the connection is established with.
23
Sommaire
1
Informations relatives au document ............................................................ 24
1.1
Mises en garde..................................................................................................................................... 24
1.2
Symboles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................................................... . . . . .
24
1.3
Symboles sur l'appareil .......................................................................................................................
24
2
Consignes de sécurité fondamentales .......................................................... 25
2.1
Exigences imposées au personnel ....................................................................................................... 25
2.2
Utilisation conforme ............................................................................................................................ 25
2.3
Sécurité du travail ................................................................................................................................
25
2.4
Sécurité de fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................................... .
25
2.5
Sécurité du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................................................ . . 26
3
Description du produit ....... ....... ...................................................................... 27
3.1
Construction de l'appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................................................... . . . . . . 27
4
Réception des marchandises et identification des produits ....................... 27
4.1
Réception des marchandises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..................................................... . . . 27
4.2
Identification du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....................................................... . 28
5
Raccordement électrique ..... ..... ..................................................................... 28
5.1
Environnement ................................................................................................................................... 29
6
Intégration système ....................................................................................... 30
6.1
Intégration de l'appareil dans le système ............................................................................................ 30
7
Mise en service ................................................................................................ 31
7.1
Contrôle du fonctionnement ............................................................................................................... 31
