Knick Ceramat WA160 Скачать руководство пользователя

Страница: 3 / 44

Safety Instructions

Ceramat® WA 160(X) Retractable Fitting

Process-Related Risks

Knick Elektronische Messgeräte GmbH & Co. KG assumes no liability for damages

caused by process-related risks known to the operator, which would in fact not permit

the use of the WA 160(X) retractable fitting.

WARNING

Always make sure that the retractable fitting cannot be activated by other persons

during servicing or installation (e.g., cleaning or replacing the sensor).

During operation the drive unit of the Ceramat® retractable fitting is rotating rather

quickly by 140°.

There is a risk of injury!

Be sure to observe:

Work on the retractable fitting shall only be performed by personnel authorized by the

operating company and specially trained for handling and operating the retractable

fitting.

Note:

Supplementary information is provided in the Ceramat WA 160(X) Maintenance

Instructions (Maintenance / Spare Parts / Accessories)

Содержание Ceramat WA160













































Результаты поиска

Содержание Ceramat WA160

Отзывы:

Похожие инструкции для Ceramat WA160

Бренды по названию

Популярные бренды

Knick Ceramat WA160, Руководство пользователя

Результаты поиска

Содержание Ceramat WA160

Отзывы:

Похожие инструкции для Ceramat WA160

Бренды по названию

Популярные бренды