Knick Ceramat WA160 Скачать руководство пользователя | Manualshive

Страница: 13 / 44

background image

13

Information on Installation

Ceramat® WA 160(X) Retractable Fitting

For operation of the Ceramat®, you must connect control air, rinsing or calibration media, and the

electrical check-back signal for indicating the probe position.

There are two possible ways to do so.

When the Ceramat is operated with a Unical® or Uniclean® electro-pneumatic controller and the

Protos® measuring system, the cables and tubings for air pressure, rinsing/calibration media and

check-back are combined in a single hose with just one plug connection (multiplug). This hose is

referred to as media connection.

This media connection is installed on the Ceramat® together with the outlet hose.

When you do not use a probe controller (Unical® or Uniclean® and Protos® measuring system), you

can connect the supply lines for control air, rinsing/calibration media and electrical check-back to

the Ceramat® with a free hose connection via the ZU 0631 standard-media interface.

Connection for operation with

Unical®/Uniclean® and Protos®

Connection for operation with

ZU 0631 standard media interface

«
...
11
12
13
14
15
...
»

Содержание Ceramat WA160













































Отзывы:

Нет отзывов

Похожие инструкции для Ceramat WA160

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Baker Instrument Company Страницы: 24

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: Zenbooth Страницы: 60

Бренд: Tate Страницы: 7

Бренд: Tate Страницы: 5

BioHarmonex BH4

Бренд: Calivita Страницы: 38

Бренд: CAIRE Страницы: 91

Бренд: Kawai Страницы: 10

Бренд: Garmin Страницы: 20

Бренд: Garmin Страницы: 10

Бренд: Naviom Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды