Knick Ceramat WA160 Скачать руководство пользователя

Страница: 29 / 44

Menu

Display

Parameter setting

Condensate drain

Interval

For daily condensate drain, specify an interval of

24 h in the "User 2" program. Confirm with "OK".

Then ”return” with the left softkey.

Probe controller

Open the “Program flow” menu.

Program flow

Select "Edit" from the "User 2" pull-down menu.

Here you can change the program name from

"User 2" to "Condensate", for example.

Suggested program flow:

01 Probe in MEASURE

02 Aux medium On 0060s

03 Aux medium Off 0015s

04 Rinse water On 0010s

05 Rinse water Off 0000s

06 Program end

Automatic Condensate Drain

Ceramat® WA 160(X) Retractable Fitting

Fixed interval (Administrator)

Interval

25.6°C

Program

7.05 pH

Interval

Program

Interval

Program

024.0 h

Off

024.0 h

Off

User 2

024.0 h

Back

Probe control (Administrator)

Controller

Back

Fixed interval

7.05 pH

Program flow

Time control

Cal preset values

Fixed interval

Installation

Unical 9000

Block

Service

Back

25.6°C

Parking

7.05 pH

User 2

Cal 2point

Cal 1point

Clean

approx. 2:40 min

Edit

approx. 2:50 min

approx. 2:26 min

approx. 2:02 min

Copy

User 2 (Administrator)

03: Aux medium OFF

Back

25.6°C

04: Rinse water ON

7.05 pH

05: Rinse water OFF

01: Probe in MEASURE

02: Aux medium ON

Program name

0010 s

Edit

0000 s

0060 s

User..2....................

0015 s

06: Program end

Program flow (Administrator)

Insert

Delete

25.6°C

Содержание Ceramat WA160













































Результаты поиска

Содержание Ceramat WA160

Отзывы:

Похожие инструкции для Ceramat WA160

Бренды по названию

Популярные бренды

Knick Ceramat WA160, Руководство пользователя

Результаты поиска

Содержание Ceramat WA160

Отзывы:

Похожие инструкции для Ceramat WA160

Бренды по названию

Популярные бренды