background image

Diaphragm Pump NMS 030 

 

Troubleshooting 

KNF Micro BA306116-306115 NMS030-EN 0221 

Operating and Installation Instructions 

13 

8.  Troubleshooting 

 

Pump does not work 

Cause 

Fault remedy 

Pump not connected to power 
supply 

  Connect pump to power

 

supply 

Power supply is not switched on 

  Switch on power supply 

Thermal switch or pump elec-
tronics have responded 

  Disconnect pump from mains power supply. 

  Allow pump to cool. 

  Identify and eliminate cause of overheating/overload 

Connections or pipes are 
blocked. 

  Check pipes and connections. 

   Remove blockage. 

External valve is closed or filter 
is blocked 

  Check external valves and filters. 

Diaphragm or valves are worn 
out. 

  Contact customer service  

Tab. 10 

 

Flow rate, pressure or vacuum to low 

The pump does not achieve the output specified in the Technical data or the data sheet 

Cause. 

Fault remedy 

Components in the system 
connected to the suction and 
pressure sides, such as hoses, 
valves or filters, are causing too 
much resistance 

  Modify installation, check the cross-sections of components 

Hose connections are not leak 
tight 

  Secure transition joints between hose and hose connections 

with clamps or clamping elements  

Particles in the pump 

  Clean the pump head, install suction-side filter if required 

Incorrect interchange of pres-
sure and suction line connec-
tions

 

  Remove pressure and suction lines and reconnect correctly 

The pump parts are not re-
sistant to the medium to be 
transferred 

  Replace the pump head with a compatible version 

Diaphragm or valves are worn 
out. 

  Contact customer service 

Tab. 11 

 

Fault cannot be rectified 

If you are unable to identify any of the above causes, please send 
the pump to KNF customer service (see address on last page). 

  Isolate the pump from the power supply and remove the pump 

from the system. 

  Clean the pump (see Chapter 7.2.1) 

  Send the pump, with completed decontamination declaration 

(see Chapter 9), to KNF customer service stating the nature of 
the transferred medium. 

Содержание NMS 030 KPDC

















Отзывы: