KMS Simplekey 4 страница 9 Скачать руководство пользователя

Страница: 9 / 52

Key Management Systems Ltd

P a g e

Specification

The following tables provide product details.

Access Provided

Doors: Controls up to 16 doors per System Controller with up to two readers per
door.
Tokens: Up to 10,000.

Controller Physical Characteristics

Dimensions (H x W): 210 x 150mm
Weight:

268g (with CM-4G)

Mounting:

Five (3.2mm) fixing holes.

Note: Upgrade controllers are supplied on a variety of backplates to
meet site requirements. Please contact KMS at [email protected] for
more information.

Communications

Mobile and I.P

based communications. See ‘Modem’ section within

manual.

Communication interface to additional components (readers etc.): KMS BUS

Memory type: Non-volatile FLASH

Baud rate: 115,200

Operating Parameters

Input voltage range: +12v to 14v DC

Current consumption at +12v DC: Average 160mA, peak 5A, 5A maximum

Lock power: +12v to 14v DC; 2A lock (maximum)

Operating temperature: -10

C to 80

C (14

F to 158

Operating humidity: 10% to 85% relative humidity, non-condensing.

Lock relay timer 1 - 255 seconds (default 5 seconds)

Door open timer 0

–

255 seconds (default 0 seconds ( off))

Содержание Simplekey 4





















































Результаты поиска

Содержание Simplekey 4

Отзывы:

Похожие инструкции для Simplekey 4

Бренды по названию

Популярные бренды

KMS Simplekey 4, Руководство по установке

Результаты поиска

Содержание Simplekey 4

Отзывы:

Похожие инструкции для Simplekey 4

Бренды по названию

Популярные бренды