KMS Simplekey 4 страница 12 Скачать руководство пользователя | Manualshive

Страница: 12 / 52

background image

Key Management Systems Ltd

12

|

P a g e

System Commissioning

Every system MUST be commissioned with KMS once the installation is complete.
Systems must NOT be commissioned before they are fully installed on site, KMS
reserve the right to nullify all warranties related to system performance unless all
steps are followed.

This is the only way of ensuring the system has been connected correctly to match
the initial configuration.

System commissioning includes the following tests:

•

Signal strength.

•

Signal Bit Error Rate.

•

Correct communications between the KMS cloud server and site based GPRS
modem.

•

Events are being received for each door on the system and events are correct
for that door.

•

Remotely unlock every door on the system to ensure all locks, readers and
outputs work as configured.

•

Make system adjustments including lock release time, door open warning
times, trades

’

profiles and any re-labelling of doors.

«
...
10
11
12
13
14
...
»

Содержание Simplekey 4





















































Отзывы:

Нет отзывов

Похожие инструкции для Simplekey 4

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: Eaton Страницы: 6

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: CORNING Страницы: 142

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

Бренд: Stramatel Страницы: 10

Бренд: NDS Страницы: 20

Бренд: Castell Страницы: 7

Бренд: CAME Страницы: 32

Бренд: JLCooper Electronics Страницы: 11

Бренд: Kathrein Страницы: 116

Бренд: Rain Bird Страницы: 104

Бренд: Entryphone Страницы: 21

MC-3000L-TC Series

Бренд: Lintec Страницы: 2

1200-RD00-00-0 Series

Бренд: gefran Страницы: 6

Бренд: YGE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды