manualshive.com logo in svg

KMS Simplekey 4, Руководство по установке

Поделиться
Скачать
KMS Simplekey 4 Скачать руководство пользователя страница 40

Key Management Systems Ltd

   

40

 | 

P a g e

 

BUS Readers 

Compatibility 

BUS readers are only compatible with Simplekey 4 Controllers at version 3401 or higher. 
BUS readers can work using KMS Sharktooth, Entrotag, PAC, Stanley and GDX proximity tokens 
and cards. 

Cabling 

BUS readers MUST be wired using Cat5, Cat5e or Cat6 cable for optimum operation. Cable 
should be pure copper, the use of CCS/CCA will degrade system performance. The maximum 
cable run will vary on installation but 100m is nominal. Up to two BUS readers can be connected 
to one Cat5e cable but please contact KMS Technical with specification of cable before 
installation. 

Installation 

There are two types of BUS reader: 
The Panel Mount BUS Reader is designed to fit within metal panels no thicker than 2.0 mm with 
a 40mm square cut-out for the front of the reader to protrude through.  
Stainless steel Vandal BUS Reader designed for surface mount on non-metallic surfaces. 
Mounting on metallic surfaces may decrease reading range. 
BUS readers come with a 0.5m flying lead Cat5 cable.  
See wiring instructions on the following page. 

Note: 

BUS Readers are uniquely addressed using the 8-digit UDN, for 

example 04000009. The reader will need to be assigned to a door by 
KMS, up to two readers can be assigned to any one door. 

 

Connection  

KMS provide a dedicated connector to wire all 
BUS readers into the system. This is known as an 
RJ45 BUS Adaptor.  
 

 

 

M2S S2MMODE 0V

12V

0V

KMS LTD SK4
RJ45 BUS ADAPTOR
ISSUE 05 © 2018

To BUS Reader(s)

To system 

connections

Содержание Simplekey 4





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды