manualshive.com logo in svg

KMS Simplekey 4, Руководство по установке

Поделиться
Скачать
KMS Simplekey 4 Скачать руководство пользователя страница 14

Key Management Systems Ltd

   

14

 | 

P a g e

 

Quick Start 

If you have installed a Simplekey 4 system previously the following procedure 
provides a quick, high-level description of the steps needed to get the system up and 
running. 

Note:

 If this is the first time you have installed a Simplekey 4 system 

the steps are described in detail in the

 

subsequent

 

pages. 

To set up a Simplekey 4 system: 

1

 

Install the Simplekey 4 controller (complete with power supply). 

2

 

Install readers, cabling and Request to Exit switches 

3

 

Install the antenna. 

4

 

Install the locks and cabling. 

5

 

Connect any auxiliary inputs. 

6

 

Commission the system with KMS. 

 

Note:

 It is essential that each component is installed and connected in line with the 

system configuration agreed with KMS. 

Each system is supplied with a full configuration document, 
connection labels and QR codes providing information as to which 
door it is to be connected. 

Commissioning the system must involve calling KMS and a walk-
through to ensure that all aspects of the system are

 

working as 

expected. 

Failure to fully commission a system may result in incorrect 
operation and reduced functionality. KMS are unable to support any 
system that has not been commissioned.  

 

 

Содержание Simplekey 4





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды