background image

 

 

36 / 97 

83000102.Ko 

 

short time. If this occurs more than three times within an hour the compressors are blocked. Before a low-
pressure fault is triggered a low-pressure warning is signalled. 

4.5.5.

 

Fan speed control 

Due to the continuous adjustment in the number of fans, the condensing pressure is kept constant depending 
on the ambient temperature by means of a PI controller. As the condensing pressure at the moment in which 
the compressor is switched on rises very fast, the PI controller is superimposed by a P controller with limiting 
setpoint. This only intervenes if the PI controller is too slow.  

4.5.6.

 

Electronic expansion valve control 

An electronic expansion valve with PI controller is used to keep the overheating constant. To prevent the 
maximum operating pressure (MOP) from being exceeded, a P controller is used, which counteracts when 
the MOP is approached and limits opening of the electronic expansion valve. 

4.5.7.

 

Temperature limit monitoring  

The temperature of the cold water feed is monitored for a minimum and maximum limit value if the chiller is 
switched on (pump is running). If the limit value is exceeded or the minimum is not reached, an alarm is 
triggered with time delay, which switches off the chiller. 

4.5.8.

 

Group fault alarm 

A group fault alarm is triggered if an alarm occurs. All alarms are included in the group fault, but not the 
warnings. The group fault signalling relay has a floating changeover contact and is energised in fault-free 
operation, in order to ensure wire break monitoring. 

4.6.

 

Execution types 

Basically, you can choose between two types of construction: 

4.6.1.

 

ECO mode 

The default setting of the Compact-Line provides for operation in ECO mode ("Run" parameter is set to "0"). 
As a result, the increase in fan speed reduces the condensing pressure to the minimum necessary value in 
the  respective  operating  point  –  the  electrical  power  consumption  of  the  overall  system  is  limited  to  a 
minimum. 

4.6.2.

 

Comfort mode 

In case of strict sound emission requirements the fan speed can be reduced to the minimum necessary value 
in the respective operating point and sound power level limited to a minimum. To do this the "Run" parameter 
must be set to "1". As a result of the lower air flow rate a reduced output of around 3% is to be expected. 
 
The optimised parameter list for your application is enclosed with the unit.  
Cleaning

 

and maintenance work in accordance with 

Chapter 10 Service

. Before work is carried out on the 

chiller the protective equipment described in 

Table 7: Definition of the safety symbols

 must be used. 

 
 
 

Содержание cBoxX 100


































































































Отзывы: