KISANKRAFT KK-CSP-5720 Скачать руководство пользователя страница 29

Страница: 29 / 52

KisanKraft

HEAVY DUTY Petrol Chainsaw

KK-CSP-5720-8650



: www.kisankraft.com



: [email protected]



: +91.80. 22178200

Page 29 of 52

No fuel in the
carburetor

No fuel in the tank

Fill the tank with fuel

Fuel valve is faulty or fuel

tank air vent is plugged.

Clear air vent hole

Lines are bent

Replace lines

2. Engine Fails To Run Smooth:

Problem

Probable Cause

Remedy

No power

Compression is
good and there
is no misfire

Air cleaner element is

plugged up.

Clean or replace air

cleaner if necessary

Air has entered fuel line

joints.

Clear the fuel line

Faulty choke lever

Replace choke lever

Carbon

build

cylinder muffler.

Clean the muffler

Compression is
bad

Burnt spark plugs

Replace the spark plug

Short in cable

Replace the cable

Bad mixture or piston ring

wear.

Replace the piston ring

Marks on cylinder. Cracks

in the piston head

Replace the piston

Engine overheated

Fuel is too low (mixture is

too thin).

Engine over oiling.

Faulty

mixture,

not

enough mixture.

Clear the lines

Carbon

piled

up,

overloaded operation.

Clean the carbon

Faulty spark plugs.

Replace the spark plugs

Plugged

cylinder

coolant lines

Clean the coolant lines

Inaccurate explosion

Carburetor not adjusted

properly.

Adjust the carburetor

gap properly

Faulty spark plugs.

Replace the spark plug

Содержание KK-CSP-5720





















































Результаты поиска

Содержание KK-CSP-5720

Отзывы:

KISANKRAFT KK-CSP-5720, Руководство пользователя, Страница: 29 / 52

Результаты поиска

Содержание KK-CSP-5720

Отзывы: