KISANKRAFT KK-CSP-5720 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

KISANKRAFT KK-CSP-5720 Скачать руководство пользователя страница 11

KisanKraft

®

HEAVY DUTY Petrol Chainsaw

KK-CSP-5720-8650



: www.kisankraft.com



: [email protected]



: +91.80. 22178200

Page 11 of 52

as follows

.

(1) Helmet

(2) Protection goggles or face Protector

(3) Thick work gloves

(4) Non-slip-sole work boots

(5) Ear protectors

b)

And you should carry with you the below given things:

(1) Attached tools and files.

(2) Properly reserved fuel and chain oil.

(3) Things to notify your working area (Rope, warning signs)

(4) Whistle (for collaboration or emergency)

(5) Hatchet or saw (for removal of obstacles)

c)

Never use the product when wearing pants with loose cuffs, when wearing sandals,
or when barefoot.

Warning Considering Handling of Fuel:

a)

The engine of this product is designed to run on a mixed fuel
which contains highly flammable petrol. Never store cans of
fuel or refill the fuel tank in any place where there is a boiler
stove, wood fire, electrical sparks, welding sparks, or any
other source of heat or fire which might ignite the fuel.

b)

Smoking while operating the product or refilling its fuel tank is extremely dangerous.
Always be sure to keep lit cigarettes away from the product at all times.

c)

When refilling the tank always turn off the engine first and take a careful look round
to make sure that there are no sparks or open flames anywhere nearby before
refueling.

d)

If any fuel spillage occurs during refueling, use a dry rag to wipe up spills before
turning the engine back on again.

e)

After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the
product to a spot 3m or more away from where it was refueled before turning on the
engine.

Before Starting Engine:

a)

Check working place, the cutting object and cutting direction. If there is obstacle,
remove it.

b)

Never start cutting until you have a clear work area, secure footing and a planned
retreat path from the failing tree.

«
...
9
10
11
12
13
...
»

Содержание KK-CSP-5720





















































Отзывы:

Нет отзывов