KISANKRAFT KK-CSP-5720 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 52

KISANKRAFT KK-CSP-5720 Скачать руководство пользователя страница 16

KisanKraft

®

HEAVY DUTY Petrol Chainsaw

KK-CSP-5720-8650



: www.kisankraft.com



: [email protected]



: +91.80. 22178200

Page 16 of 52

INSTALLING GUIDE BAR AND SAW CHAIN

WARNING

The saw chain has very sharp edges. Use thick protective gloves for safety.

1)

Pull the guard towards the front handle to
check that the chain brake is not on.

2)

Loosen the nuts and remove the chain
cover.

3)

Install the bar over the bar bolts .Place the
bar in its rearmost position. Place the chain
the drive sprocket locate it in the groove on
the bar. Begin on the top edge of the bar

WARNING

Make sure that the edges of the cutting links are facing forward on the top edge of the
bar.

4)

Fit the chain cover and locate the chain
adjuster pin in the hole in the bar. Check
that the drive links of the chain fit correctly
over the drive sprocket and that the chain
is correctly located in the groove in the
bar. Tighten the bar nuts finger tight.

5)

Tension the chain by turning the chain
tensioning screw clockwise using the
combination spanner.

«
...
14
15
16
17
18
...
»

Содержание KK-CSP-5720





















































Отзывы:

Нет отзывов