Kipor SINEMASTER IG4300 Скачать руководство пользователя страница 8

 

To ensure safe operation:

 

 

Gasoline  is  extremely  flammable  and  explosive  under  certain 

conditions. Refuel in a well ventilated area with the engine stopped. 

Keep  away  from  smoking  materials,  sparks  and  other  sources  of 

combustion  when  refueling  the  generator.  Always  refuel  in  a 

well-ventilated location. 

Wipe up spilled gasoline at once.

   

Restrict use of the generator in

 high-hazard risk

 areas. 

 

Connections for standby power to a building's electrical system must 

be made by a qualified electrician and must comply with all applicable 

laws and electrical codes. Improper connections can allow electrical 

current  from  the  generator  to  back  feed  into  the  utility  lines.  Such 

back  feed  may  electrocute  utility  company  workers  or  others  who 

contact  the  lines  during  a  power  outage,  and  when  utility  power  is 

restored,  the  generator  may  explode,  burn,  or  cause  fires  in  the 

building's  electrical  system.  This  generator  is  not  designed  to  be 

connected  to  an  automatic  transfer  switch.  Serious  damage  to  the 

engine and inverter module may result. 

 

  Always make a pre-operation inspection before you start the engine.                       

Place  the  generator  at  least  three  feet  or  one  meter  away  from 

buildings or other equipment during operation. 

Operate the generator on a level surface to prevent fuel spillage or oil 

starvation. 

Know how to stop the generator quickly and understand operation of 

all    the  controls.    Never  permit  anyone  to  operate  the  generator 

without  proper  instructions.  Keep  children  and  pets  away  from  the 

generator when it is in operation. 

Never  operate  the  generator  with  the  door  open  or  any  panels 

removed.  Do  not  operate  in  any  enclosure  such  as  an  RV 

compartment. 

Keep away from rotating parts while the generator is running. 

The  generator  is  a  potential  source  of  electrical  shocks  when 

misused; do not operate with wet hands. 

Do not operate the generator in rain or snow or let it get wet. 

Содержание SINEMASTER IG4300



















































Отзывы: