KIOUR MACON HP Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 9

KIOUR MACON HP Скачать руководство пользователя страница 9

*!!*

Versions: V2.1.060721. Parameters: 97C1i,103F1i, 109C2i,115F2i

*!!*

Made in Greece

ATTENTION

: according to safety standards, the device must be properly positioned and protected from any contact with electrical parts. The device must be fastened in such a way that it

cannot be removed without the use of tools. Disconnect the main safety switch of the installation before proceeding to any maintenance. Disconnect the power supply of the device before

proceeding to any maintenance. Do not place the device near heat sources, equipment containing strong magnets, in areas affected by direct sunlight or rain. Prevent electrostatic discharges
and sharp objects from been inserted to the device. Separate signal cables from power supply cables to prevent electromagnetic disorders. Signal cables must never be in the same pipe with

the power supply cables.
The device is under two year

’

s guarantee. The guarantee is valid only if the manual instructions have been applied. The control and service of the device must be done by an authorized

technician. The guarantee covers only the replacement or the service of the device.

preserves the right to adjust its products without further notice.

392 Mesogeion Avenue Agia Paraskevi 153 41 Τ: 210 6533730 F: 210 6546331 [email protected] www.kiour.com

V2.1.080721

«
...
7
8
9

Содержание MACON HP










Отзывы:

Нет отзывов