Kingsman OB24MAN Скачать руководство пользователя страница 23

Страница: 23 / 54

20lb Cylinder Installation - Fire Table - Custom Installations

Fire Tables -20LB Cylinder In Unit-

⚠

Only a 20LB LP Cylinder may be used inside the Fire Table Enclosure.

NOTE:

Cylinders acceptable for use inside this appliance must be compatible with the retention means shown here.



The LP gas supply cylinder used with LP models

must be constructed and marked in accordance

with the specifications for LP-gas cylinders of the

U.S. Department of Transportation (DOT)

Specifications for LP-Gas Cylinders, or the
Standard for Cylinders, Spheres and Tubes for
Transportation of Dangerous Goods and
Commission

, CAN/CSA-B339, as applicable.



The LP gas supply cylinder used with LP models

must be provided with a listed overfilling

prevention device.



The pressure regulator and hose assembly

supplied with LP models (PN#

27FP-900FF

) must

be used. Replacement pressure regulators and

hose assemblies must be those specified in this

manual.



Always check for gas leaks with a soap and water

solution. DO NOT USE OPEN FLAME FOR LEAK

TESTING.



When an LP model is not in use, the LP-gas must

be turned off at the supply cylinder.

CUSTOM INSTALLATIONS
TANK RETAINER - Included with all MAP Burners and LP

Conversion Kits

1. Connect foot ring of 20lb

Cylinder to Tank Retainer with

thumbscrew.

2. Fasten Tank Retainer to

mounting surface.

3. Concrete anchor

required for concrete

surface (not supplied).

Foot Ring Drops

into Round Hole

Replace

Tank Brace

Slide over Protective

Collar of 20lb cylinder

and tighten.

Tank Retainer for Custom

Installations.

NOT USED ON FIRE TABLES.

Installation of 20lb Cylinder

into Fire Tables:



Remove Top Clamp.



Connect 20lb cylinder to

regulator.



Place 20lb cylinder into

Fire Table as shown.



Secure 20lb cylinder with

Tank Brace as shown.

Tank Brace

Содержание OB24MAN























































Результаты поиска

Содержание OB24MAN

Отзывы:

Похожие инструкции для OB24MAN

Бренды по названию

Популярные бренды

Kingsman OB24MAN, Руководство пользователя

Результаты поиска

Содержание OB24MAN

Отзывы:

Похожие инструкции для OB24MAN

Бренды по названию

Популярные бренды