Kingsman Fireplaces MQZCVBG34LPE2 Скачать руководство пользователя страница 44

Страница: 44 / 80

MQZCVBG34

RBCB1 Cannonballs

-Option

Assorted size and colors. Place randomly as desired inside fireplace.

Can be used with MQ Glass, MQ Ember, and / or Lava Rock.

Do not place Cannonballs directly on burner ports.

If sooting occurs change position of or remove affected objects.

•

MQ Glass can be placed directly on Burner and on Glass Tray (Maximum 5 LBS of Glass).

•

MQ Ember can be placed directly on Burner Only.

•

Lava Rock (Supplied with Base Unit) CANNOT be placed on Burner.

Place Lava Rock in channel in front of

Glass Tray & on Glass Tray.

NOTE

•

Pilot Area Must Not Be Covered, as delayed ignition can occur.

•

Do not place Cannonballs directly on burner ports.

*Pilot Shield should be visually
inspected monthly for signs of
deterioration due to flame
exposure. Replace if necessary.

Pilot Area Must Not

Be Covered

Содержание MQZCVBG34LPE2

















































































Результаты поиска

Содержание MQZCVBG34LPE2

Отзывы:

Похожие инструкции для MQZCVBG34LPE2

Бренды по названию

Популярные бренды

Kingsman Fireplaces MQZCVBG34LPE2, Руководство по установке

Результаты поиска

Содержание MQZCVBG34LPE2

Отзывы:

Похожие инструкции для MQZCVBG34LPE2

Бренды по названию

Популярные бренды