Kinghome KW09CQ2B8A, Руководство по обслуживанию

Страница: 71 / 202

68
Technical Information
Service Manual
Function introduction for combination buttons
Replacement of batteries in remote controller
1. Energy-saving function
1.
Under ON status, press "Mode" and "Turbo" button simultaneously,the "
WiFi
" icon will be displayed on remote controller.
press "Mode"and"Turbo" button simultaneously,the " WiFi " icon will disppear.
Operation guide
After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner.
2.
3. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT.
4.
Press "▲" or " ▲ " button to set your required temperature. (Temperature cant be adjusted under auto mode).
Press "FAN" button to set your required fan speed: auto, low, medium and high speed.
Press "SWING" button to select fan blowing angle.
5.
● During operation, point the remote control signal sender at the receiving window on indoor unit.
● The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles between them.
●
indoor unit during operation.
Replace new batteries of the same model when replacement is required. ●
● When you dont use remote controller for a long time, please take out the batteries.
● If the display on remote controller is fuzzy or theres no display, please replace batteries.
2. 8
ć
heating function
3. Child lock function
4. Temperature display switchover function
Under energy-saving function, fan speed is defaulted at auto speed and it cant be adjusted. ●
●
Sleep function and energy-saving function cant operate at the same time. If energy-saving function has been set under cooling mode,
Under energy-saving function, set temperature cant be adjusted. Press "TURBO" button and the remote controller wont send signal.
●
press sleep button will cancel energy-saving function. If sleep function has been set under cooling mode, start up the energy-saving
function will cancel sleep function.
Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to start up or turn off energy-saving function. When energy-saving
function is started up, "SE" will be shown on remote controller, and air conditioner will adjust the set temperature automatically according to
ex-factory setting to reach to the best energy-saving effect. Press "TEMP" and "CLOCK"buttons simultaneously again to exit energy-saving
function.
Note:
● Under 8
ć
heating function, fan speed is defaulted at auto speed and it cant be adjusted.
●
● Under 8
ć
heating function, set temperature cant be adjusted. Press "TURBO" button and the remote controller wont send signal.
Sleep function and 8
ć
heating function cant operate at the same time. If 8
ć
heating function has been set under cooling mode, press
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start up or turn off 8
ć
heating function. When this function is
started up, " " and "8
ć
" will be shown on remote controller, and the air conditioner keep the heating status at 8
ć
. Press "TEMP" and
"CLOCK" buttons simultaneously again to exit 8
ć
heating function.
Note:
●
sleep button will cancel 8
ć
heating function. If sleep function has been set under cooling mode, start up the 8
ć
heating function will
cancel sleep function.
Under
̧
temperature display, the remote controller will display 46
̧
heating.
1.
Under OFF status, press " ▲ " and "MODE" buttons simultaneously to switch temperature display between
ć
and
̧
.
Press "▲" and " ▲ " simultaneously to turn on or turn off child lock function. When child lock function is on, " " icon is displayed on remote
controller. If you operate the remote controller, the " " icon will blink three times without sending signal to the unit.
2.
out the cover of battery box along the arrow direction.
Replace two 7# (AAA 1.5V) dry batteries, and make sure the position of "+" polar and "-" polar are correct.
Reinstall the cover of battery box.
3.
Note:
signal sender battery
Cover of battery box
remove
reinstall
WIFI fuction 5.
If “H1” is displayed on the remote controller while it’s not operated by the professional person/after-sales person, it belongs to the misoperation.
Please operate it as below to cancel it.Under the OFF status of remote controller, hold the Mode button for 5s to cancel “H1” display.
Note:
● If remote controller displays “H1”, it belongs to the normal function reminder. If the unit is defrosting under heating mode, it operates according
to H1 defrosting mode. “H1” won’t be displayed on the panel of indoor unit;
● Once you set H1 mode, if you turn off unit by remote controller, H1 will display 3 times on the remote controller and then disappear;
● Also, when you set H1 mode, when you change to heating mode, H1 will display 3 times on the remote controller and then disappear.