Kingfisher KI 2300 Series Скачать руководство пользователя страница 60

Страница: 60 / 74

PERFORMANCE VERIFICATION TESTS

KI2000 UM-6

58 -

Optical Light Source

Centre wavelength and Spectral Bandwidth (FWHM) Test

(optional)

Connect the Light Source to OSA as shown.

Switch on the instruments and allow to fully warm up.

On Light Source, enable the source and set the wavelength to
1310 nm.

On the OSA, press the [Instr Preset] key

Press [Auto/Meas] and wait until 'End of Automeasure' is
displayed

Choose [User] and select the type of source to be measured
(FP for Fabry Perot laser).

To show the display in linear mode:



Press [Menu].



Press [Amptd] on the left side of the display.



Press [Linear] on the right side of the display.

To ensure interference - free reading of the display it is
advisable to stop the repeating calculations.



Press [User].



Press [Single Sweep].

If the trace on the display is not clear, you can change
resolution by using the span key.

From the displayed measurements check and note the values
for "mean wavelength" (Centre wavelength) and "FWHM"
(Spectral Bandwidth) in the test report, Table 6.

10.

Repeat the test with the source wavelength set to 1550 nm.

Test set-up for the Centre wavelength and Spectral Bandwidth test

Содержание KI 2300 Series











































































Результаты поиска

Содержание KI 2300 Series

Отзывы:

Похожие инструкции для KI 2300 Series

Бренды по названию

Популярные бренды

Kingfisher KI 2300 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание KI 2300 Series

Отзывы:

Похожие инструкции для KI 2300 Series

Бренды по названию

Популярные бренды