King gates ELEVO, Инструкции и предупреждения по установке и использованию

Страница: 18 / 28

18
EN
10. Devices connectable
to the control unit
1
12
34
56
78
91
0
11
12
23
4
ON
DIP
13 14
10.8
10.8
10.2
10.2
10.1
10.5
10.6
10.7
10.4
10.3
1
12
34
56
78
91
0
11
12
23
4
ON
DIP
13 14
10.8
10.8
10.2
10.2
10.1
10.5
10.6
10.7
10.4
10.3
1
12
34
56
78
91
0
11
12
23
4
ON
DIP
13 14
10.8
10.8
10.2
10.2
10.1
10.5
10.6
10.7
10.4
10.3
The control unit is prearranged for interfacing with different devic-
es dedicated to system control, system safety and other addition-
al functions. Below is a list of their connections and corresponding
functions.
10.1 - Transformer
Standard transformer of the system (supplied and connected) is
230Vac*(primary) to 0-22.5-32Vac (secondary) to the control unit.
10.2 - Motor
The maximum connectable load is 100W (max 3A) per motor.
10.3 - Warning light
TERMINALS: 1-2.
The warning light is an accessory used for signaling any movement
of the gate leaf.
Connected lamps: 24V 15W maximum power.
10.4 - AUX contact
TERMINALS: 11-12.
Default setting: 12V electric lock operation.
The AUX can be set to electric lock, magnetic lock, courtesy light
(monostable or bistable). Also, voltage output is customizable to 24V.
To change the AUX setup, refer to the advanced programming
functions of Paragraph 13:
- Selection of AUX output type (Paragraph 13.1) = set as lock or
courtesy light;
- Selection of AUX operating mode (Paragraph 13.2) = allows for
customizing the contact’s operation;
- Selection of AUX contact voltage (Paragraph 13.3) = allows for
selecting the AUX contact voltage (12V or 24V).
10.5 - Safety devices
TERMINALS: 4-9-10.
Control unit has two safety inputs available for voltage free (dry con-
tact) connection(s).
“S2 Photo” CLOSING or OPENING/CLOSING PHASE SAFETY DEVICES
Terminals 4,8 allow connection of safety devices active during closing
and opening phase. This input is normally closed (NC). For infra-red
photocells and safety edges with micro-switch contact.
The factory wire bridge connected to S2 Photo must be removed
when using this input.
These devices intervene during the gate’s closing and opening phase
according to DIP switch 4 (see par. 4.1).
In particular:
DIP4 set to ON:
- during the closing phase they invert the movement direction and
re-open the door fully
- during the opening phase they have no effect
- with the opened door they lock closing commands
- with the closed door they have no effect
DIP4 set to OFF:
- during the closing phase they lock the movement and re-open the
door fully when released
- during the opening phase they lock the movement and re-open
the door fully when released
- with the opened door they lock closing commands
- with the closed door they lock opening commands
Figures 38a, 38b and 38c show examples of King Gates “Viky30”
photocell connections.
When multiple devices are connected on this contact, they
must be series connected (see Fig. 38c).
If more photocell pairs are connected, RX and TX units of
the safety set should be cross installed (see Fig. 38c).
“S1 Edge” OPENING/CLOSING PHASE SAFETY DEVICES
It is possible to connect devices (e.g. photocells or edges) with nor-
mally closed (NC) contact or 8K2 resistive edges to the “S1 Edge”
input (terminal 9-10).
The factory wire bridge connected to PHO2 must be removed when
using this input.
These devices intervene while the door is moving, in particular:
- with the closed door they lock opening commands.
- with the opened door they lock closing commands.
- during the closing phase they command a brief inversion
- during the opening phase they command a brief inversion
Figures 38a, 38b and 38c show examples of King Gates “Viky30”
photocell connections.
When multiple devices are connected on this contact, they
must be series connected (see Fig. 38c).
37