manualshive.com logo in svg

Kinesys Elevation 1 Plus, Руководство по эксплуатации продукта

Поделиться
Скачать
Kinesys Elevation 1 Plus Скачать руководство пользователя страница 28

28

Elevation 1+

© 2011 Kinesys Projects Ltd

13

Manual and Remote Running

In  addition  be  being  controlled  by  an  external  computer  Elevation  1+  units  can  be
controlled  locally  by  both  on-board  controls  or  by  connecting  a  remote  pendant
controller. The methods are known as manual and remote running respectively.

Manual Running

At the left hand end of the front display panel on the Elevation 1+ are two buttons and a
rotary  speed  control.  These  controls  allow  the  hoist  to  be  moved  at  variable  speed
directly from the unit. While the Elevation 1+ is in manual running mode run commands
from the controlling computer will be ignored.

To  enter  manual  mode  press  the  menu  and  enter  buttons  together.  The  display  will
change  to  show  the  word  ‘manual’  and  the  indicators  in  the  up  and  down  manual
running buttons will illuminate. To move the hoist ensure the speed control is set to its
slowest speed (turn the knob fully anti-clockwise) and then press and hold either up or
down depending on the  desired  direction.  Slowly increase the  speed  until  the  desired
running  speed  has  been  reached.  To  stop  movement,  either  release  the  run  button
which will stop the device with a quick ramp or return the speed control to zero and then
release the button which will offer a more gradual ramp down. In all cases the unit will
not allow the hoist to be run further than its soft limits unless they have been overridden.
Once manual running is completed return the unit to automatic mode  by pressing  the
menu  and  enter  buttons  together.  The  word  ‘auto’  will  be  displayed  and  computer
running  will  then  be  possible  again.  The  unit  will  time  out  of  manual  mode  after  two
minutes of inactivity.

Remote Running

Remote running is a feature that allows the Elevation 1+ to be operated remotely by a
LodeStar ‘pickle’ or other similar pendant controller. It allows the hoist to be run up and
down between its limits at a speed determined by the default speed setting within the
unit.  The  hoist  is  ramped  up  and  down  when  the  run  buttons  on  the  pendant  are
pressed and released and the buttons must be held during the entire movement of the
hoist.

Содержание Elevation 1 Plus





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды