Page 3
Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX 626/330-3861
Ballast Access and Replacement:
Make certain electricity is
OFF
before
accessing/replacing ballast.
1. Adjust fixture in an upright position to ease
ballast replacement. (Refer to Fixture
Adjustment Instructions above)
2. Loosen three (3) captive screws while
holding ballast compartment cover. Lower
cover until the internal chain supports the
weight of the cover.
3. Disconnect power supply and ground leads.
Disconnect black and white leads extending
to lamp compartment.
4. Remove four (4) #8-32 hex nuts and
lockwashers located on each corner of
ballast core. Grab ballast assembly with both
hands, (
Caution
: assembly weighs
approximately 35 lbs.), slide ballast away
from studs.
5. Replace the ballast assembly with proper
type and wattage. Secure assembly with four
(4) #8-32 hex nuts and lockwashers.
6. Connect lamp leads, power supply and
ground leads i.e., green-to ground, white-to-
common, and black-to-voltage. Locate wire
connectors away from ballast core and coil.
7. Replace ballast compartment cover being
careful not to pinch any wires between cover
and housing. Tighten screws progressively
and evenly to a hand-snug condition with
F
”
allen wrench.
Replacement Parts:
Please consult factory for
any needed parts.
Cover Safety
Chain
(3)
J
-20
Captive Socket
Cap Screws
with Sealing
O-Rings (
F
”
Allen Wrench)
(4) #8-32 Hex Nuts with
Lockwashers. Secures Ballast
Assembly to Ballast Compartment
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and
accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim
Products, are warranted to be free from defects of material and/or
workmanship for a period of 1 year from date of sale, with the following
exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the component
manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be warranted
against defects of material and/or workmanship, and failure due to
corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade, shall be
warranted against defects of material and/or workmanship, and failure
due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil,
shall be warranted against defects of material and/or workmanship for a
period of 3 years from date of sale. Aluminum fixture components in
direct contact with soil shall be warranted from defects of material and
failure from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance
with applicable Kim instructions, specifications and accepted trade
practices, are covered by the Kim Warranty. During the warranty
period, with proof of purchase, Kim will repair or replace with the same
or similar product, at Kim's option, without charge. Labor costs are the
owner's responsibility and are excluded from this warranty. This
warranty is void if the product is modified, tampered with, misapplied,
poorly installed, improperly maintained, or subjected to abnormal
conditions.
Repair or replacement as provided under this warranty is the exclusive
remedy of the purchaser. This warranty is in lieu of all other warranties,
expressed or implied, including any implied warranty of fitness for a
particular application. Kim Lighting shall not be liable to the purchaser
for indirect or consequential damages.
AFL30 Architectural Floodlight
Installation Instructions
AFL31
Horizonal Flood
AFL32
Vertical Flood
AFL33
Medium Flood
!
AFL34
Narrow Flood
AFL35
Spot
AFL36
Narrow Spot
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
