KidKraft F270855 Скачать руководство пользователя | Manualshive

Страница: 7 / 76

background image

7

This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.

Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!

Check that assembly is square
before tightening bolts.

Use a measuring tape to assure
proper location.

Check that set or assembly is properly level
before proceeding.

Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of  wood.

This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.

Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.

Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.

Symbols

Throughout these instructions symbols are provided as important reminders for proper and safe assembly.

Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.

For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” (8mm) is slightly
larger than 1/4” (6.4mm).

Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.

Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.

Use

Help

Use

Help

Measure

Distance

Square

Assembly

Use

Level

Pre-drill 1/8”(3mm) & 3/16”(5mm) Bit

Tighten

Bolts

CAUTION – Protrusion Hazard

Keys to Assembly Success

Tools Required

Quantity

Key Number

Part Description,
Part Size

2X 1012 P

No

Yes

Lag Assembly

Bolt Assembly

Flat Washer

Lag Screw

Hex Bolt

Lock
Washer

Flat
Washer

Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
(3.2mm) pilot holes

T-Nut
(Hammer into place)
Do not crush wood!

If Bolt protrudes
beyond T-Nut

Use an extra
flat washer

• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• Rubber Mallet

• #1 Phillips, #2 Robertson

and Screwdriver

• Ratchet with extension

1/2” (13mm) & 9/16”(14 mm)
sockets

• Open End Wrench

1/2” (13mm) & 9/16”(14 mm)

• Adjustable Wrench
• 1/8”(3mm) & 3/16”(5mm)
Drill Bits

• 3/16”(5mm) Hex Key
• 8’ (2.4m) Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil

3mm

5mm

ost 2 x 4 x 83” (5 cm x 10 cm x 210 cm)

«
...
5
6
7
8
9
...
»

Содержание F270855













































































Отзывы:

Нет отзывов

Похожие инструкции для F270855

Бренд: XDP Recreation Страницы: 40

Бренд: i-CAT Страницы: 96

Бренд: ABB Страницы: 16

Бренд: MacDon Страницы: 238

Бренд: Land Pride Страницы: 72

Бренд: Venue Страницы: 20

Бренд: Delta Light Страницы: 2

Бренд: Tuv nord Страницы: 23

Бренд: YOKOGAWA Страницы: 2

Fake Plastic Trees

Бренд: AUDIO KITCHEN Страницы: 8

Бренд: Graci-lite Страницы: 2

PTB220TS / CASE

Бренд: Vaisala Страницы: 10

Бренд: Kellfri Страницы: 16

Бренд: KAM Страницы: 11

Бренд: NANLITE Страницы: 22

Бренд: Numark Страницы: 40

Martin Exterior 400

Бренд: Harman Страницы: 40

Бренд: Dwyer Instruments Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды