KidKraft F270855 Скачать руководство пользователя

Страница: 35 / 76

Step 13: Back Frame Assembly

Attach (1860) MK Mount to (1873) Back Floor with 1 (H13) 1/4 x 3-1/2” Hex Bolt (with lock washer, flat washer

and t-nut) and to (1857) Top Back with 1 (H12) 1/4 x 3” Hex Bolt (with lock washer, flat washer and t-nut). (fig.

13.1 and 13.2)

Make sure (1857) Top Back is level and the distance between the bottom of (1857) Top Back and the top of

(1873) Back Floor is 28-5/8”, then attach to both (1500) Posts using 4 (S7) #12 x 2” Pan Screws (with 3/16” flat

washers). (fig. 13.2)

Wood Parts

Hardware

Fig. 13.2

4 x

#12 x 2 Pan Screw (3/16” flat washer)

1 x

1/4 x 3” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 3-1/2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

Top Back 1 x 4 x 46-1/2”

1 x

MK Mount 2 x 3 x 34-13/16”

1857

1860

1500

H12

1500

1857

H13

1860

1873

1500

1857

1500

1860

1873

Fig. 13.1

H12

H13

1/4” lock

washer

1/4” flat

washer

1/4” t-nut

1/4” lock

washer

1/4” flat

washer

1/4” t-nut

with 3/16”

flat washer

with 3/16”

flat washer

28-5/8”

Содержание F270855













































































Результаты поиска

Содержание F270855

Отзывы:

Похожие инструкции для F270855

Бренды по названию

Популярные бренды

KidKraft F270855, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F270855

Отзывы:

Похожие инструкции для F270855

Бренды по названию

Популярные бренды