manualshive.com logo in svg

KidKraft F270855, Инструкция по установке и эксплуатации, Страница: 63 / 76

Поделиться
Скачать
KidKraft F270855 Скачать руководство пользователя страница 63

 63 

Step 31:  Attach Roof to Fort

A: 

 With two helpers place the Roof Assembly, from Step 9, on the fort as shown in fig. 31.1.  The roof should 

be centred on the Roof Frame assembly and (0863) Roof Supports should be flush to the inside of the fort 

and resting on (1865) SW Roof Side and (1864) SL Roof Side.  The (0501) Joists should fit tight to the inside 

of each (0357) Tarp Front Back.

B:  

Predrill and attach (0357) Tarp Front Back to (0501) Joists using 1 (S2) #8 x 1-1/2” Wood Screw per side. 

(fig. 31.1 and 31.2)

C:  

Attach 1 (0514) Roof Brace to each (0863) Roof Support so it is tight against the angled edge of the Roof 

Supports using 2 (S2) #8 x 1-1/2” Wood Screws per brace.  (fig. 31.3 and 31.4)

D:  

Attach each (0514) Roof Brace to (1865) SW Roof Side and (1864) SL Roof Side using 2 (S1) #8 x 1-1/8” 

Wood Screws per brace.  (fig. 31.3 and 31.4)

C

C

Hardware

Wood Parts

Door Window

0357

S2

Fig. 31.1

Fig. 31.2

0501

0357

0501

1865

0863

1864

0501

0357

Fig. 31.4

Fig. 31.3

0863

0514

1865

S1

S2

0514

0514

0514

0863

  8 x 

#8 x 1-1/8” Wood Screw

10 x 

#8 x 1-1/2” Wood Screw

4 x 

Roof Brace 1 x 6 x 13”

0514

S1

S2

Содержание F270855













































































Отзывы:

Нет отзывов