KidKraft F270855 Скачать руководство пользователя страница 23

Страница: 23 / 76

Step 6: Monkey Rail Assembly

Pre-drill all pilot holes using a 1/8” drill bit before installing wood screws.

Fig. 6.1

Fig. 6.3

Note: Pilot holes at

bottom of this rail

Insert 3 (578) 1-1/8 x 15-7/8” Dowels into both (1564) MK Rail Longs as shown in fig. 6.1. Note the pilot holes in

one of the (1564) MK Rail Long are on the bottom of the board.

Note: Pilot holes

at top of board

Attach (578) 1-1/8 x 15-7/8” Dowels to both rails with 2 (S3) #8 x 2-1/2” Wood Screws per dowel. (fig. 6.3)

Make sure shoulder of dowel is against

each rail before pre-drilling pilot holes. Drill

1/8” pilot holes through the rails and into the

dowels to prevent splitting. (fig. 6.2)

Fig. 6.2

Wood Parts

Hardware

6 x

#8 x 2-1/2” Wood Screw

3 x

Tennon Dowel 1-1/8 x 15-7/8”

2 x

MK Rail Long 2 x 4 x 52”

578

1564

578

1564

578

1564

578

1564

3/4”

Содержание F270855













































































Результаты поиска

Содержание F270855

Отзывы:

KidKraft F270855, Инструкция по установке и эксплуатации, Страница: 23 / 76

Результаты поиска

Содержание F270855

Отзывы: