KidKraft Cedar Summit DEVONSHIRE ELITE Скачать руководство пользователя

Страница: 73 / 100

Hardware

On the Fort End of (9452) Engineered SW Beam attach 2 Heavy Flat Brackets with 2 (G21) 5/16 x 3-3/4”

Hex Bolts (with 2 flat washers and 1 lock nut). (fig. 29.4 & 29.5)

Place (9352) SW Mount in between both Heavy Flat Brackets . Attach (9352) SW Mount to Heavy Flat

Brackets with 2 (G21) 5/16 x 3-3/4” Hex Bolts (with 2 flat washers and 1 lock nut) (fig 29.4). Install a 5/16” t-nut

into the bottom pre-drilled hole in the (9352) SW Mount as shown in fig. 29.6.

Place 1 Heavy L-Bracket against (9452) Engineered SW Beam and (9352) SW Mount . Attach with 1 (G17)

3/8 x 6” Hex Bolt (with 2 flat washers and lock nut) and 1 (G10) 5/16 x 3” Hex Bolt (with lock washer, flat

washer and t-nut). (fig 29.7)

4 x

5/16 x 3-3/4” Hex Bolt (FW2 x 2, LN2)

1 x

3/8 x 6” Hex Bolt (FW10 x 2 & LN3)

1 x 5/16 x 3” Hex Bolt (LW2, FW2, TN2)
1 x

Other Parts

2 x Heavy Flat Bracket
1 x Heavy L-Bracket

G21

G17

G10

Wood Parts

1 x

SW Mount 3 x 3 x 16”

9352

Fort End

Fig. 29.5

Fig. 29.7

G17

Heavy Flat

Bracket

Fig. 29.4

9352

G10

Heavy

L-Bracket

9452

Fig. 29.6

Step 29: Swing Beam Assembly

Part 2

Note: It is important to note

hole orientation for this step.

G21

FW2

TN2

FW2

LW2

LN3

FW10

TN2

LN2

Содержание Cedar Summit DEVONSHIRE ELITE





































































































Результаты поиска

Содержание Cedar Summit DEVONSHIRE ELITE

Отзывы:

Похожие инструкции для Cedar Summit DEVONSHIRE ELITE

Бренды по названию

Популярные бренды

KidKraft Cedar Summit DEVONSHIRE ELITE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cedar Summit DEVONSHIRE ELITE

Отзывы:

Похожие инструкции для Cedar Summit DEVONSHIRE ELITE

Бренды по названию

Популярные бренды