manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Инструкция по установке и эксплуатации, Страница: 62 / 100

Поделиться
Скачать
KidKraft Cedar Summit DEVONSHIRE ELITE Скачать руководство пользователя страница 62

 62 

Hardware

1 x 

Support Diagonal 15/16 x 3-1/4 x 23-11/16”

Wood Parts

9269

C:

 Place (9269) Support Diagonal so that the angled end is flush to the front edge and to the bottom of (9239) 

Left Rail . The opposite end should be tight against (9360) Back Post Left . Attach (9269) Support Diagonal to 

(9239) Left Rail using 1 (H10) 1/4 x 2-1/4” Hex Bolt (with flat washer, lock washer and t-nut).  (fig. 22.5)

D:

 Center 1 Corner Panel Bracket on each side of (9269) Support Diagonal so that each bracket is flat against 

the brace and the wall panel as shown in (fig. 22.6). Attach each Corner Panel Bracket using 4 (S0) #8 x 7/8” 

Truss Head Screws . (fig. 22.4 and 22.6)

9372

9239

8 x 

#8 x 7/8” Truss Head Screw

S0

9372

9360

9269

9360

9269

9269

Flush

per bracket

x 4

Other Parts

2 x Corner Panel 

Bracket

Corner Panel Bracket

S0

1 x  

1/4 x 2-1/4” Hex Bolt

 

(LW1, FW1, TN1)

H10

H10

Fig. 22.4

Fig. 22.5

Fig. 22.6

Step 22: Attach Access Ladder/Rockwall 

Part 3

9213

TN1

FW1

LW1

Содержание Cedar Summit DEVONSHIRE ELITE





































































































Отзывы:

Нет отзывов