KidKraft BOULDER STATION Скачать руководство пользователя

Страница: 5 / 100

About Our Wood

KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we

take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible

to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?

One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is

different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can

result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of

the product:
1.

Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)

because the surface and interior moisture content will vary more widely than in thinner wood.

Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid

wetting and drying of the wood.

Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.

How can I reduce the amount of weathering to my Play System?

At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption

during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a

water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are

concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.

Complete and mail registration card to receive important product notifications and assure prompt

warranty service.

5 Year Limited Warranty

KidKraft warrants that this product is free from defect in materials and workmanship for a period of one

year from the original date of purchase. In addition, lumber is warranted for 5 years against structural

failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and

slides carry a one-year warranty only.

This warranty applies to the original owner and registrant and is non-transferable.

Regular maintenance is required to assure the integrity of your Play System. This warranty does not

cover any inspection cost.
This Limited Warranty does not cover:

• Labor for replacement of any defective item(s);

• Incidental or consequential damages;

• Cosmetic defects which do not affect performance or integrity;

• Vandalism; improper use or installation; acts of nature;

• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not

affect performance or integrity.

KidKraft products have been designed for safety and quality. Any modifications made to the original

product could damage the structural integrity of the unit leading to failure and possible injury.

Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids

any and all warranties.
This product is warranted for

RESIDENTIAL USE ONLY

. Under no circumstance should a

KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day

cares and the like. Such use may lead to product failure and potential injury. Any and all public use

will void this warranty.

KidKraft disclaims all other representations and warranties of any kind, express or implied.

This Warranty gives you speciﬁc legal rights. You may have other rights as well which vary from state to state or

province to province. This warranty excludes all consequential damages, however, some states do not allow the

limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.

Содержание BOULDER STATION





































































































Результаты поиска

Содержание BOULDER STATION

Отзывы:

Похожие инструкции для BOULDER STATION

Бренды по названию

Популярные бренды

KidKraft BOULDER STATION, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BOULDER STATION

Отзывы:

Похожие инструкции для BOULDER STATION

Бренды по названию

Популярные бренды