Keysight U3020AS26 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 41

background image

Keysight U3020A User’s and Service Guide

35

CAUTION

The Mains wiring and connectors shall be compatible with the connector used in the

premise electrical system. Failure, to ensure adequate earth grounding by not using the

correct components may cause product damage, and serious injury.

CAUTION

This product is designed for use in Installation Category II and Pollution Degree 2.

CAUTION

Before switching on this instrument, make sure the supply voltage is in the specified range.

CAUTION

Verify that the premise electrical voltage supply is within the range specified on the

instrument.

CAUTION

Ventilation Requirements: When installing the instrument in a cabinet, the convection into

and out of the instrument must not be restricted. The ambient temperature (outside the

cabinet) must be less than the maximum operating temperature of the instrument by 4 °C

for every 100 watts dissipated in the cabinet. If the total power dissipated in the cabinet is

greater than 800 watts, forced convection must be used.

WARNING

These servicing instructions are for use by qualified personnel only. To avoid electrical
shock, do not perform any servicing unless you are qualified to do so.

WARNING

Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended. Discard used batteries according to manufacturer’s
instructions.

WARNING

For continued protection against fire hazard replace line fuse only with same type and
rating. The use of other fuses or material is prohibited.

WARNING

These servicing instructions are for use by qualified personnel only. To avoid electrical
shock, do not perform any servicing unless you are qualified to do so.

«
...
33
34
35
36
37
...
»

Содержание U3020AS26










































Отзывы:

Нет отзывов

Похожие инструкции для U3020AS26

Бренд: Bartscher Страницы: 22

Бренд: GE Страницы: 138

Бренд: 3M Страницы: 2

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: Konica Minolta Страницы: 32

Бренд: Ocean Sonics Страницы: 45

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: Kanlux Страницы: 4

Бренд: Atlas Metal Страницы: 2

Бренд: Meritor Страницы: 65

Бренд: TEUCER Страницы: 4

Бренд: ABS Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды