Keysight N5221BU-677 Скачать руководство пользователя

Страница: 9 / 54

Installation Note N5222-90129 9

Getting Prepared

Protecting Your Workspace from Electrostatic Discharge

For information, click on the Chapter 1 bookmark, “Electrostatic Discharge
Protection” in the PDF Service Guide

ESD Equipment Required for the Installation

Tools Required for the Installation

1. See

“Downloading the Online PNA Service Guide” on page 7

Description

Keysight Part Number

ESD grounding wrist strap

9300-1367

5-ft grounding cord for wrist strap

9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire

9300-0797

ESD heel strap (for use with conductive floors)

9300-1308

Description

Qty

T-6 TORX driver - set to 4 in-lbs (0.45 N.m)

T-10 TORX driver - set to 9 in-lbs (1.02 N.m)

T-20 TORX driver - set to 21 in-lbs (2.38 N.m)

5/16-in (8 mm) nutsetter or open end torque wrench- set to 8 in-lbs (0.9 N.m)

5/16-in (8 mm) nutsetter or open end torque wrench - set to 10 in-lbs (1.13 N.m)

5/16-in (8 mm) nutsetter or open end torque wrench - set to 21 in-lbs (2.38 N.m)

3/16-in (5 mm) nutsetter or open end torque wrench - set to 6 in-lbs (0.68 N.m)

5/8-in (16 mm) nutsetter or open end torque wrench - set to 21 in-lbs (2.38 N.m)

1-in (25.4 mm) torque wrench - set to 72 in-lbs (8.15 N.m)

Use a 5/16-in torque wrench set to 10 in-lbs on all cable connections

except the front and rear panel bulkhead connectors. On these, use a 5/16

inch nutsetter or open end torque wrench set to 21 in-lb.

Содержание N5221BU-677























































Результаты поиска

Содержание N5221BU-677

Отзывы:

Похожие инструкции для N5221BU-677

Бренды по названию

Популярные бренды

Keysight N5221BU-677, Установочная инструкция

Результаты поиска

Содержание N5221BU-677

Отзывы:

Похожие инструкции для N5221BU-677

Бренды по названию

Популярные бренды