Keysight N5221BU-677 Скачать руководство пользователя

Страница: 50 / 54

50 Installation Note N5222-90129

Installation Procedure for the Upgrade

on-line HELP. A list of equipment required to perform these adjustments is also

found in the service guide.
To view this service guide information, click the Chapter 3 bookmark “Tests
and Adjustments” in the PDF Service Guide

After the specified adjustments have been performed, the analyzer should

operate and phase lock over its entire frequency range.

EEPROM Backup

The analyzer uses arrays of correction constants to enable the analyzer to

produce accurate, leveled source signals and receive clean test signals. These

constants are stored in non-volatile EEPROM memory and in flash memory

files.
The adjustments listed here generate new correction constants. The analyzer

must have a backup of this new data in case any of the data becomes

corrupted.
To store the backup data, perform these steps:

— Navigate to the EEPROM Backup Utility, located at:

—

Windows 7 --

C:\Program Files (x86)\Keysight\Network

Analyzer\Service\eebackup.exe

— Windows 10 --

C:\Program Files\Keysight\Network

Analyzer\Service\eebackup.exe

— Run the program.
— Click Backup EEPROM.
— Click Backup TSMB Mem.
— Click Exit when the program has finished.

Operator’s Check

Perform the Operator’s Check to check the basic functionality of the analyzer.

For instructions, click the Chapter 3 bookmark “Tests and Adjustments” in the
PDF Service Guide

f you experience difficulty with the basic functioning of the analyzer, contact

Keysight. Refer to

“Contacting Keysight” on page 4

1. See

“Downloading the Online PNA Service Guide” on page 7

Содержание N5221BU-677























































Результаты поиска

Содержание N5221BU-677

Отзывы:

Похожие инструкции для N5221BU-677

Бренды по названию

Популярные бренды

Keysight N5221BU-677, Установочная инструкция

Результаты поиска

Содержание N5221BU-677

Отзывы:

Похожие инструкции для N5221BU-677

Бренды по названию

Популярные бренды