Keysight N5221BU-677 Скачать руководство пользователя

Страница: 17 / 54

Installation Note N5222-90129

Installation Procedure for the Upgrade

Step 2. Remove the Outer Cover

For instructions, click the Chapter 7 bookmark “Removing the Covers” in the
PDF Service Guide

Step 3. Remove the Inner Cover

For instructions, click the Chapter 7 bookmark “Removing the Covers” in
the PDF Service Guide

Step 4. Remove the Front Panel Assembly

For instructions, click the Chapter 7 bookmark “Removing and Replacing
the Front Panel Assembly” in the PDF Service Guide

Step 5. Remove the A23 Test Set Motherboard

For instructions, click the Chapter 7 bookmark “Removing and Replacing
the A23 test set motherboard” in the PDF Service Guide

Step 6. Remove Some Bottom-Side (Test Set) Cables

1. Place the analyzer bottom-side up on a flat surface.
2. Remove the following cables. To see an image showing the location of

these cables, click the Chapter 6 bookmark “Bottom RF Cables, Standard
2-Port Configuration, Option 217

, S/N Prefix

≥

6021

” in the PDF Service

Guide

These cables may be discarded - they will not be reinstalled.

—W

(N5222-20073) A21 HMA26.5 to A23 mixer brick

—W48 (N5222-20003) A33 reference mixer switch to A23 mixer brick (R1)
—W12 (N5222-20068) A29 port 1 coupler to front-panel Port 1 CPLR THRU

1. See

“Downloading the Online PNA Service Guide” on page 7

Be careful not to damage the center pins of the semirigid cables. Some

flexing of the cables may be necessary but do not over-bend them.

Leave the gray flexible cables, the wire harnesses, and the ribbon cables

connected where possible. Any that are removed should be labeled for

reconnection later.
Remove and save the cable guards for the front panel jumpers.
When removing a cable, also remove the plastic cable clamp, if present. It

is normal for some of the cable clamp’s adhesive to remain.

Содержание N5221BU-677























































Результаты поиска

Содержание N5221BU-677

Отзывы:

Похожие инструкции для N5221BU-677

Бренды по названию

Популярные бренды

Keysight N5221BU-677, Установочная инструкция

Результаты поиска

Содержание N5221BU-677

Отзывы:

Похожие инструкции для N5221BU-677

Бренды по названию

Популярные бренды