Keysight E8718A Скачать руководство пользователя

Страница: 6 / 53

Keysight E8718A Radar Target Simulator User Guide

Safety Symbols

The following symbols on the instrument and in the documentation indicate

precautions which must be taken to maintain safe operation of the instrument.

Alternating current (AC)

Both direct and alternating current

Off (mains supply)

Caution, risk of electric shock

Caution, hot surface

Caution, risk of danger (refer to this

manual for specific Warning or Caution

information)

Earth (ground) terminal

Protective earth (ground) terminal

Frame or chassis (ground) terminal

Terminal is at earth potential. Used for

measurement and control circuits

designed to be operated with one

terminal at earth potential.

Terminal for neutral conductor on

permanently installed equipment

Terminal for line conductor on

permanently installed equipment

Standby (supply): units with this

symbol are not completely

disconnected from ac mains when this

switch is off. To completely disconnect

the unit from ac mains, either

disconnect the power cord or have a

qualified technician install an external

switch.

Complies with FDA performance

standards for laser products except for

deviations. Persuant to Laser Notice

No.50 June 24 2007.

Содержание E8718A






















































Результаты поиска

Содержание E8718A

Отзывы:

Похожие инструкции для E8718A

Бренды по названию

Популярные бренды

Keysight E8718A, Руководство пользователя

Результаты поиска

Содержание E8718A

Отзывы:

Похожие инструкции для E8718A

Бренды по названию

Популярные бренды