Keysight E1458A Скачать руководство пользователя | Manualshive

Страница: 11 / 46

background image

Keysight E1458A 96-Channel Digital I/O Module Service Guide

13

Safety Considerations

General Information

USING AUTOTRANSFORMERS. If the mainframe is to be

energized via an autotransformer (for voltage reduction)

make sure the common terminal is connected to neutral

(that is, the grounded side of the main’s supply).
CAPACITOR VOLTAGES. Capacitors inside the mainframe

may remain charged even when the mainframe has been

disconnected from its source of supply.
USE PROPER FUSES. For continued protection against fire

hazard, replace the line fuses only with fuses of the same

current rating and type (such as normal blow, time delay,

etc.). Do not use repaired fuses or short-circuited

fuseholders.
SHOCK HAZARD. Only service-trained personnel who are

aware of the hazards involved should install, remove, or

configure the Module or expander. Before you remove any

installed module, disconnect AC power from the

mainframe and from other modules that may be connected

to the Module or expander.
CHANNEL WIRING INSULATION. All channels that have a

common connection must be insulated so that the user is

protected from electrical shock. This means wiring for all

channels must be insulated as though each channel carries

the voltage of the highest voltage channel.

MAXIMUM INPUTS. The maximum voltage that can be applied to

any terminal is 42 V Peak. The maximum current on any data line

is

±

48 mA. The maximum current on any handshake line is

±

40

mA.
STATIC ELECTRICITY. Static electricity is a major cause of

component failure. To prevent damage to the electrical

components in the module, observe anti-static techniques

whenever working on the device.
PARTS REMOVAL. This module uses a surface mount assembly.

Special soldering equipment is required for parts removal or

replacement. Use of standard soldering equipment will cause

damage to the PC board and is not covered under warranty.

«
...
9
10
11
12
13
...
»

Содержание E1458A















































Отзывы:

Нет отзывов

Похожие инструкции для E1458A

Бренд: Laser Страницы: 2

Бренд: TCS Страницы: 28

Бренд: Union Instruments Страницы: 63

Бренд: Zeck Audio Страницы: 16

Бренд: Nelson Страницы: 14

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: Dahua Страницы: 28

Passport Conference 2 Series

Бренд: Fender Страницы: 20

Бренд: Newco Страницы: 13

Бренд: Ricon Страницы: 96

Бренд: Secure Home Страницы: 160

Бренд: M-system Страницы: 4

Бренд: JBL Страницы: 8

Бренд: FARFISA INTERCOMS Страницы: 4

Kontron 3.5"-eIO-GPA

Бренд: S&T Страницы: 37

Бренд: Tyco Fire Product Страницы: 8

Бренд: National Instruments Страницы: 13

Бренд: SereneLife Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды