Keysight E1458A Скачать руководство пользователя | Manualshive

Страница: 10 / 46

background image

12

Keysight E1458A 96-Channel Digital I/O Module Service Guide

General Information

Safety Considerations

Safety Considerations

This product is a Safety Class I instrument that is provided with a protective earth
terminal when installed in the mainframe. The instrument, mainframe, and all
related documentation should be reviewed for familiarization with safety
markings and instructions before operation or service.

Refer to the WARNINGS page in this manual for a summary of safety information.
Safety information for testing and service follows and is also found throughout
this manual.

Warnings and Cautions

This section contains WARNINGS which must be followed for your protection
and CAUTIONS which must be followed to avoid damage to the equipment when
performing instrument maintenance or repair.

SERVICE-TRAINED PERSONNEL ONLY. The information in

this manual is for service-trained personnel who are

familiar with electronic circuitry and are aware of the

hazards involved. To avoid personal injury or damage to

the instrument, do not perform procedures in this manual

or do any servicing unless you are qualified to do so.
CHECK MAINFRAME POWER SETTINGS. Before applying

power, verify that the mainframe setting matches the line

voltage and that the correct fuse is installed. An

uninterruptible safety earth ground must be provided from

the main power source to the supplied power cord set.
GROUNDING REQUIREMENTS. Interruption of the

protective (grounding) conductor (inside or outside the

mainframe) or disconnecting the protective earth terminal

will cause a potential shock hazard that could result in

personal injury. (Grounding one conductor of a

two-conductor outlet is not sufficient protection.)
IMPAIRED PROTECTION. Whenever it is likely that

instrument protection has been impaired, the mainframe

must be made inoperative and be secured against any

unintended operation.
REMOVE POWER IF POSSIBLE. Some procedures in this

manual may be performed with power supplied to the

mainframe while protective covers are removed. Energy

available at many points may, if contacted, result in

personal injury. (If maintenance can be performed without

power applied, the power should be removed.)

«
...
8
9
10
11
12
...
»

Содержание E1458A















































Отзывы:

Нет отзывов

Похожие инструкции для E1458A

Бренд: Rain Bird Страницы: 8

Бренд: Panasonic Страницы: 2

RXD15 - RADIO CASSETTE W/CD

Бренд: Panasonic Страницы: 8

Бренд: Garaventa Lift Страницы: 58

Бренд: Bentel Security Страницы: 4

Бренд: Dannmar Страницы: 85

Бренд: Watts Страницы: 24

Бренд: b-red Страницы: 28

Бренд: Roule Страницы: 6

Бренд: Toro Страницы: 28

Бренд: Nilfisk-Advance Страницы: 84

Бренд: PAPILLON Страницы: 8

Бренд: auna multimedia Страницы: 9

Бренд: Oase Страницы: 87

Satmix 2.1 PA system

Бренд: Fun Generation Страницы: 32

Бренд: morse Страницы: 9

Бренд: morse Страницы: 10

Бренд: SoundRyder Audio Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды