manualshive.com logo in svg

Keysight E1458A, Руководство по обслуживанию

Поделиться
Скачать
Keysight E1458A Скачать руководство пользователя страница 19

Keysight E1458A 96-Channel Digital I/O Module

Service Guide

21

2

Verification Tests

Introduction

This chapter describes the verification tests for the Keysight E1458A module. The 

three levels of test procedures described in this chapter are used to verify that 

the Keysight E1458A:

–

is functional (Functional Verification Test)

–

meets selected testable specifications (Operation Verification)

–

meets all testable specifications (Performance Verification)

Test Conditions/ Procedures

See Table 1-1 for test equipment requirements. You should complete the 

Performance Verification tests at least once a year. For heavy use or severe 

operating environments, perform the tests more often. The verification tests 

assume that the person performing the tests understands how to operate the 

mainframe, the module, and the specified test equipment. The test procedures 

do not specify equipment settings for test equipment except in general terms. It 

is assumed that a qualified, service-trained technician will select and connect 

the cables, adapters, and probes required for the test.
The tests in this chapter assume that the Keysight E1458A has the switch and 

jumper settings shown in Table 2-1 and Figure 2-1. Use the blank column in 

Table 2-1 to record the starting switch or jumper positions. Set the switches back 

to their original positions when you are finished testing.

You must have correctly installed a downloadable Digital I/O 

Driver into the command module to run these tests. Refer to the 

Installation Note provided with the Driver or to the Keysight 

E1405B/E1406A User’s Manual for driver downloading 

procedures.

Table 2-1

Keysight E1458A Test Conditions

Switch

Setting for Verification Tests

Recorded Setting

IRQ

1

LADDR

144 (18)

PULL-UP ENABLE

All Ports ENABLED

PORT/FLAG COMBINING

All Ports NOT COMBINED

Содержание E1458A















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды