Keysight Technologies InfiniiVision 2000 Скачать руководство пользователя страница 67

Страница: 67 / 86

Troubleshooting

2000/3000 X-Series Oscilloscopes Service Guide

Successfully passing Hardware Self Test does not guarantee 100% of the

oscilloscope's functionality. Hardware Self Test is designed to provide an 80%

confidence level that the oscilloscope is operating properly.

To perform front panel self test

Pressing

[Utility] > Service > Front Panel Self Test

lets you test the front panel keys

and knobs as well as the oscilloscope display.

Follow the on-screen instructions.

Failures in the front panel self test indicate problems with the keyboard, keypad, or

display.

To verify default setup

The oscilloscope is designed to turn on with the setup from the last turn on or

previous setup.

To recall the default setup:

Press the

[Default Setup]

key.

This returns the oscilloscope to its default settings and places the oscilloscope

in a known operating condition. The major default settings are:

•

Horizontal

•

main mode.

•

100 us/div scale.

•

0 s delay.

•

center time reference.

•

Vertical

•

Channel 1 on.

•

5 V/div scale.

•

dc coupling.

•

0 V position.

•

probe factor to 1.0 if an AutoProbe probe is not connected to the channel.

•

Trigger

•

Edge trigger.

•

Auto sweep mode.

Содержание InfiniiVision 2000























































































Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 2000, Руководство по обслуживанию

Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды