Keysight Technologies InfiniiVision 2000 Скачать руководство пользователя страница 28

Страница: 28 / 86

2000/3000 X-Series Oscilloscopes Service Guide

Testing Performance

When testing 3000 X-Series MSOs, use the 8-by-2 test connector to connect

digital channels D15-D8 to the output of the precision source. Then connect

the D15-D8 ground lead to the ground side of the 8-by-2 connector.

Repeat this procedure (steps 6 through 8) for digital channels D15-D8 to verify

threshold accuracy and record the threshold levels in the Performance Test

Record (see

page 53

). Be sure to set the thresholds with the

User

softkey for the

appropriate set of channels.

To verify DC vertical gain accuracy

This test verifies the accuracy of the analog channel DC vertical gain for each

channel.

In this test, you will measure the dc voltage output of a precision source using the

oscilloscope’s

Average - Full Screen

voltage measurement and compare the results

with the multimeter reading.

Table 6

DC Vertical Gain Accuracy Test Limits

Models

Test Limits

Notes

2000 X-Series

±3% of full scale (>= 10 mV/div);

±4% of full scale (< 10 mV/div)

•

Full scale is defined as 32 mV on the 2 mV/div range

and the 1 mV/div range.

•

Full scale on all other ranges is defined as 8 divisions

times the V/div setting.

3000 X-Series

±2.0% of full scale

Содержание InfiniiVision 2000























































































Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiVision 2000, Руководство по обслуживанию

Результаты поиска

Содержание InfiniiVision 2000

Отзывы:

Похожие инструкции для InfiniiVision 2000

Бренды по названию

Популярные бренды