Keysight Technologies 85091D Скачать руководство пользователя страница 92

Страница: 92 / 172

4-10 Electronic Calibration Modules Reference Guide

Use, Maintenance, and Care of the Devices
Gaging Connectors

When to Gage Connectors

Gage a connector at the following times:

— Prior to using an ECal module for the first time: record the pin depth

measurement so that it can be compared with future readings. This serves

as a good troubleshooting tool when you suspect damage may have

occurred to the device.

— If either visual inspection or electrical performance suggests that the

connector interface may be out of typical range (due to wear or damage, for

example).

— If a module is used by someone else, or on another system or piece of

equipment.

— Initially after every 100 connections, and after that as often as experience

suggests.

Recognizing Gage Types

A gage is referred to by the sex of the connector it measures. For example, a

male gage measures male connectors and therefore has a corresponding

female connector.

— See

Figure 4-3 on page 4-11

for an illustration of a typical gage for

3.5 mm, 2.92mm, 2.4 mm, and 1.85 mm connectors.

— See

Figure 4-4 on page 4-12

for an illustration of a typical gage for Type-N

connectors.

— See

Figure 4-5 on page 4-13

for an illustration of a typical gage for 7 mm

connectors.

Reading the Connector Gage

The gage dial is divided up into increments of 0.0001 inch (0.0025 mm) and

major divisions of 0.001 inch (0.0025 mm). For Type-N gages, see

Figure 4-4

on page 4-12

. For each revolution of the large dial, the smaller dial indicates a

change of 0.01 inch (0.025 mm). Use the small dial as the indicator of

multiples of 0.01 inch (0.0025 mm). In most connector measuring applications,

this value will be zero.

When using the 7 mm ECal Kit module, you must remove the 7 mm collet

before gaging the pin depth of the connectors. Refer to

“Gaging

Connectors” on page 4-9

for gaging instructions. Use the collet extraction

tool provided in your 7 mm kit to remove the collet.

A 3.5 mm gage set can measure 3.5 mm and 2.92 mm connectors. And, a

2.4 mm gage set can measure 2.4 mm and 1.85 mm connectors.

Содержание 85091D













































































































































































Результаты поиска

Содержание 85091D

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies 85091D, Справочное руководство

Результаты поиска

Содержание 85091D

Отзывы:

Бренды по названию

Популярные бренды