Keysight Technologies 85091D Скачать руководство пользователя страница 74

Страница: 74 / 172

3-8 Electronic Calibration Modules Reference Guide

Operating ECal Module
Setting Up a Calibration

Calibration Methods for Non-Insertable Devices

A “non-insertable” device means that the measurement ports cannot be

connected together to establish a THRU connection during calibration for

transmission. Because the module typically forms the THRU path, you can use

one of the following methods to perform a calibration for non-insertable

devices:

Configure ECal Module the Same as Device

The simplest way to calibrate for non-insertable devices is to configure an ECal

module with the same connector types as the DUT. RF ECal modules can be

configured with mixed connectors to match the connector types on the DUT.

Refer to

“Models and Options” on page 1-4

. You can also configure the

module with different connector types by performing a User-Characterization

(see below).

Use Adapter Removal Calibration

Adapter removal provides an accurate way to calibrate for non-insertable

devices, but requires extra calibration steps to characterize the adapter. The

adapter type used for this calibration must be a -m- to -m- or -f- to -f- and

have the same connector type as the module. In addition, the module must

have a male connector on one test port and a female connector on the other

test port (of the same connector type).

Use Unknown Thru Calibration

Unknown Thru calibration is currently available with all PNA network analyzers

except the E8801/2/3A. It is easy to perform and can be used on any two ports

when using a multiport PNA. It causes minimal cable movement if the Thru

standard has the same footprint as the DUT. In fact, the DUT can often be the

Thru standard. A 1-port calibration is performed on both ports. The unknown

Thru is connected between the two ports and measured. Next, the user must

confirm the Estimated Delay. This requires knowing the phase response to

within 1/4 wavelength. If the phase response is unknown, the Delay value can

be measured independently and entered in the dialog box.

Perform a User-Characterization

Normally, when you perform a calibration with an ECal module, the error terms

for a calibration are computed using the factory characterization (data) stored

in the module. User-Characterization allows you change the characterization

of the module in two ways:

— Change the connector configuration: allows you to add an adapter or fixture

to the test port of the module and embed the effects into the

characterization of the module. The result of the new characterization

extends the reference plane from one or more of the module’s test ports to

those on the adapter (or fixture).

Содержание 85091D













































































































































































Результаты поиска

Содержание 85091D

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies 85091D, Справочное руководство

Результаты поиска

Содержание 85091D

Отзывы:

Бренды по названию

Популярные бренды