manualshive.com logo in svg

Keysight Technologies 85091D, Справочное руководство

Поделиться
Скачать
Keysight Technologies 85091D Скачать руководство пользователя страница 38

 1-30                                                                                Electronic Calibration Modules Reference Guide

General Information
Service and Recertification

1-

— the part number and serial number of each device
— type of service required
— a detailed description of the problem and how the device was being used 

when the problem occurred (such as calibration or measurement) 

Recertification of ECal Modules

The suggested interval for recertification is 12 months. After reviewing the 

results of the initial recertification, you may establish a shorter interval that 

reflects greater use and wear of the module.

Where to Send a Module for Recertification

Contact Keysight for information on where to send your kit for recertification. 

See 

“Contacting Keysight” on page 1-29

. Refer to 

“Returning Devices to 

Keysight” on page 1-29

 for instructions on the preparation of returning the 

device.

How Keysight Verifies Your ECal Module

Keysight verifies the specifications of these devices as follows:

1.

The residual microwave error terms of the test system are verified with 

precision airlines and shorts or low frequency resistance that are directly 

traced to the National Institute of Standards and Technology (NIST). The 

airline and short characteristics are developed from mechanical 

measurements. The mechanical measurements and material properties 

are carefully modeled to give very accurate electrical representation. The 

mechanical measurements are then traced to NIST through various plug 

and ring gages and other mechanical measurements.

2.

Each module is electrically tested on this system to the specification listed 

in 

Chapter 5, “Specifications and Characteristics.”

These two steps establish a traceable link to NIST for Keysight to the extent 

allowed by the Institute's calibration facility. The specifications data provided 

for the module are traceable to NIST through Keysight Technologies.

When transporting the module, use original or comparable packaging.

Only Keysight calibration laboratories use the most accurate reference 

standards - directly traceable to national and international primary 

standards - to calibrate ECal modules to their warranted specifications. 

Calibration services performed by unauthorized calibration service 

providers will cause ECal modules to perform substantially below 

specifications. Keysight is not responsible for the poor performance of ECal 

modules that are calibrated by such unauthorized calibration service 

providers.

Содержание 85091D













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды