Keyscan CA8WL-AL Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 52

background image

Keyscan Inc. A Member of the Kaba Group – CA8WL-AL Rev. B Installation Guide (07.15)

33

Program On-board Ethernet
Module

The CA8WL-AL has an on-board Ethernet module – serial to Ethernet converter – which must be programmed
using the Keyscan NETCOM Program Utility when the CA8WL-AL is used on a network (TCP/IP).

If you are configuring the CA8WL-AL for reverse network communication use the procedures outlined in the
next section – Configure CA8WL-AL for Reverse Network Communication.

NETCOM Program Utility

The CA8WL-AL Rev. B control board requires NETCOM Program Utility – version 6.0.18 or higher. Always use
the latest NETCOM Program Utility on the enclosed Keyscan CD when programming the on-board Ethernet
module. The CA8WL-AL Rev. B control board is distinguished by DIP switches which are not on previous
CA8WL-AL control boards.

Before You Start Programming

Before you start programming the CA8WL-AL’s on-board Ethernet module, ensure that you have the following
items:



Serial data cable with loose conductors (Keyscan p/n 40-2322)



Have the latest NETCOM Program Utility – version 6.0.18 or higher - contained on the enclosed Keyscan
Utilities & Drivers CD installed on a PC/laptop that can be serially connected to the CA8WL-AL



Obtained an IP address, subnet mask, and, if required, a gateway from an IT administrator or authorized
source



Know the CA8WL-AL’s baud rate setting – 57,600 BPS or 115,200 BPS



Know the PC/laptop’s COM port with the serial data cable connection to the CA8WL-AL’s RS-232 terminal
for programming the on-board Ethernet module



Keyscan recommends that you perform the restore default settings procedures on page 18 before
programming the CA8WL-AL’s Ethernet module.

Installing the NETCOM Program Utility

The NETCOM Program Utility is a Keyscan application that programs the CA8WL-AL’s on-board Ethernet
module with an IP address and other settings. The utility must be installed on a PC or laptop that can be
serially connected to the CA8WL-AL’s RS-232 communication terminal. If the PC or laptop only has USB ports,
use Keyscan’s optional USB-SER adaptor.

To install the NETCOM Program Utility, insert the Keyscan Utilities & Drivers CD in the PC/laptop CD or DVD
drive. The utility is programmed to auto-start when the disk is inserted in the disk drive. Follow the on-screen
prompts. Please remember the NETCOM Program Utility must be installed before you can program the CA8WL-
AL on-board Ethernet module.

Program the CA8WL-AL On-board Ethernet Module

1.

Ensure that the CA8WL-AL has power either from a PoE source or a +12V DC power supply.

«
...
31
32
33
34
35
...
»

Содержание CA8WL-AL





















































Отзывы:

Нет отзывов

Похожие инструкции для CA8WL-AL

Бренд: Jedia Страницы: 12

Бренд: JED Micro Страницы: 10

Бренд: JCM Technologies Страницы: 2

Бренд: U-Prox Страницы: 3

Бренд: Zamel Страницы: 2

Бренд: XtendLan Страницы: 12

Бренд: phytron Страницы: 55

VENMAR ADVANCED TOUCHSCREEN CONTROL

Бренд: vanEE Страницы: 4

Бренд: GOAL ZERO Страницы: 52

Бренд: YASKAWA Страницы: 42

Бренд: YASKAWA Страницы: 351

Бренд: Gardena Страницы: 15

Бренд: Holars AS Страницы: 15

Бренд: Jung Страницы: 8

CYPRESS Traveo S6J335 Series

Бренд: Infineon Technologies Страницы: 308

Бренд: Zamel Страницы: 2

Бренд: Maxon Страницы: 64

Бренд: National Instruments Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды