Keyscan CA8WL-AL Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

Keyscan Inc. A Member of the Kaba Group – CA8WL-AL Rev. B Installation Guide (07.15)

15

S1.5 - Reader LED Mode

This DIP switch is not applicable.

S1.6 - Unassigned

Reserved for future use.

S1.7 - Temporary Card Countdown

The Client software has a card usage countdown function when credentials are issued on a temporary basis. To
employ this function in the Client software, the temporary card countdown DIP switch must be enabled on the
CA8WL-AL control board.

S1.8 – N/A

This DIP switch is not applicable.

S1.9 - Clear Memory Enable

The S1.9 DIP switch must be on to enable the J1 Clear Memory jumper for restoring the factory defaults.

S1.10 & S1.11 - Communication Terminal Activation

DIP switches S1.10 and S1.11 activate the RS-232 terminal for direct serial communication or network
communication with the internal, on-board Ethernet module for run mode or program mode.

S1.12 - Flash Program Memory Upgrade

Currently, this function is unavailable.

«
...
13
14
15
16
17
...
»

Содержание CA8WL-AL





















































Отзывы:

Нет отзывов

Похожие инструкции для CA8WL-AL

Бренд: Parker Страницы: 30

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Gardena Страницы: 17

Бренд: Badger Meter Страницы: 16

Бренд: Harsco Industrial Страницы: 57

Бренд: S&C Страницы: 24

Бренд: Trane Technologies Страницы: 8

Бренд: Freescale Semiconductor Страницы: 34

Бренд: Matelec Страницы: 2

Бренд: Danfoss Страницы: 4

Бренд: National Instruments Страницы: 18

Бренд: Azbil Страницы: 220

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды