Keyscan CA8WL-AL Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

background image

Keyscan Inc. A Member of the Kaba Group – CA8WL-AL Rev. B Installation Guide (07.15)

30

Diagnostics

The CA8WL-AL has communication and system status LEDs on the left side of the control unit for diagnostics.

Communication LEDs

The CA8WL-AL has on-board LEDs for communication diagnostics outlined in the table below. If calling
Keyscan for technical support, indicating the state of the LED assists our technicians in isolating potential
difficulties.

Table 4 – Communication LEDs

CA8WL-AL Control Board

LED

State of LED

Notes

TD 1 - Green

Flashing – normal

Main processor sending data to RS-485 port

Not Illuminated – abnormal
condition

Follow restore factory defaults J1 procedure in attempt to resolve.

Illuminated – abnormal
condition

Follow restore factory defaults J1 procedure in attempt to resolve.

RD 1 - Red

Flashing – normal

Main processor receiving data from RS-485 port

Not Illuminated – abnormal
condition

Follow restore factory defaults J1 procedure in attempt to resolve

Illuminated – abnormal
condition

Follow restore factory defaults J1 procedure in attempt to resolve

Possible wiring fault

TD 2 – Green

Flashing – normal

Control board sending data via communication path determined by S1.10

& S1.11 to Client/Communication Mgr

Not Illuminated

If Client/Comms not polling the control board

If S1.10 & S1.11 are configured for on-board NETCOMP programming

Illuminated – abnormal
condition

Follow restore factory defaults J1 procedure in attempt to resolve

RD 2 – Red

Flashing – normal

Control board receiving data via communication path determined by
S1.10 & S1.11 from Client/Communication Mgr

Not Illuminated

If Client/Comms not polling the control board

If S1.10 & S1.11 are configured for on-board NETCOMP programming

Illuminated – abnormal
condition

Possible wiring fault

«
...
28
29
30
31
32
...
»

Содержание CA8WL-AL





















































Отзывы:

Нет отзывов

Похожие инструкции для CA8WL-AL

Бренд: Oceanic Страницы: 13

Бренд: FrSky Страницы: 2

Бренд: S&C Страницы: 24

Бренд: Gateway Страницы: 2

Бренд: Oriental motor Страницы: 4

Бренд: Stramatel Страницы: 10

Enclosure ENCR-10

Бренд: suprema Страницы: 18

Бренд: Mita Страницы: 7

Бренд: PXM Страницы: 15

Бренд: Holars AS Страницы: 15

Бренд: Gardenic Страницы: 14

Бренд: meibes Страницы: 20

Бренд: Telit Wireless Solutions Страницы: 49

Бренд: Danfoss Страницы: 8

EscapeKeeper JR

Бренд: Fright Ideas Страницы: 2

Бренд: IEI Technology Страницы: 81

SN32F260 Series

Бренд: SONIX Страницы: 141

Бренд: Inverter Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды